Installing engine
- dcil
-
Topic Author
- Offline
- User
-

Registered
- Posts: 9
- Thanks: 0
Installing engine
25 Feb 2011 20:48
I'm in the process of building a 1982 kz750 twin into a chopper. I've cut the side bars out that follow the backbone in preperation for raking, plus it gives more room for engine removal/installation. I pulled the motor out this evening(major pain by myself). After the framework and paint are done, how is the best way to get it back in there without raping the paint? I took it out laying on it's side, but it fits so close I scratched the sidecover on the frame. There has to be a trick that I'm missing. Thought about pulling the head, but thats a whole other can of worms I don't want to open unless I have to. Any input will be greatly appreciated.
Please Log in or Create an account to join the conversation.
- purls
-
- Offline
- User
-

Registered
- Posts: 91
- Thanks: 0
Re: Installing engine
25 Feb 2011 21:00 - 25 Feb 2011 21:02
1983 KZ750 Spectre
1978 KZ650B2A
1978 KZ650B2A
Last edit: 25 Feb 2011 21:02 by purls.
Please Log in or Create an account to join the conversation.
- PLUMMEN
-
- Offline
- User
-

Registered
- Posts: 7983
- Thanks: 104
Re: Installing engine
25 Feb 2011 21:10
i normally lay motor on its side on a rug and lower frame over it,wrap frame tubes to protect them.
removing exhuast studs before installing motor also helps
removing exhuast studs before installing motor also helps
Still recovering,some days are better than others.
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: Installing engine
26 Feb 2011 07:36 - 26 Feb 2011 07:37
With Frame stripped (front end & rear swingarm off), cylinder/head/carbs off...
Frame on blanket laying vertical....
Frame tubes where engine slides in bubble wrapped/tapped...
Slide lower engine into place just off right side as sitting over frame...
Left arm inside frame, right arm outside of frame...
2-4" lift up and slide frame left into place...
Shift/move/rotate engine in mounting hole positions.
Insert engine mounting bolts....
Eat your spinach, helps if you're a strong sonsabitch as well....
:laugh:
Frame on blanket laying vertical....
Frame tubes where engine slides in bubble wrapped/tapped...
Slide lower engine into place just off right side as sitting over frame...
Left arm inside frame, right arm outside of frame...
2-4" lift up and slide frame left into place...
Shift/move/rotate engine in mounting hole positions.
Insert engine mounting bolts....
Eat your spinach, helps if you're a strong sonsabitch as well....
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Last edit: 26 Feb 2011 07:37 by Old Man Rock.
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: Installing engine
26 Feb 2011 07:44
PLUMMEN wrote:
I just pick the whole damn engine up and hold in place with my lefthand, while I run the bolts thru with the other. :laugh: :laugh: :laugh:
No seriously, I do the same thing, but with an old mattress and some wood pieces to shim the motor where I want it.
i normally lay motor on its side on a rug and lower frame over it,wrap frame tubes to protect them.
removing exhuast studs before installing motor also helps
I just pick the whole damn engine up and hold in place with my lefthand, while I run the bolts thru with the other. :laugh: :laugh: :laugh:
No seriously, I do the same thing, but with an old mattress and some wood pieces to shim the motor where I want it.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- PLUMMEN
-
- Offline
- User
-

Registered
- Posts: 7983
- Thanks: 104
Re: Installing engine
26 Feb 2011 08:59
i used to be superman also! :laugh:
Still recovering,some days are better than others.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
