Broken bolts...OMG!
- pete@PMH
-
Topic Author
- Offline
- User
-

Registered
- Posts: 18
- Thanks: 0
Broken bolts...OMG!
11 Mar 2011 22:25
Okay...so whilst removing carb boots from my 650 cylinder head, 3 of the machine screws broke off. After 3 days of soaking them with penetrating oil, drilling right through the remaining stud and testing my 'easy out' tool to the extreme, no luck...any ideas? I'd like to question the term 'EASY'...!
'79 KZ650C,
Re-Building '78 KZ650B
Re-Building '78 KZ650B
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: Broken bolts...OMG!
11 Mar 2011 22:37
that sucks! i usually have better luck with the head removed from motor,makes it easier to work on.
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- kzgpzzrx
-
- Offline
- User
-

Registered
- Posts: 34
- Thanks: 0
Please Log in or Create an account to join the conversation.
- Samwell
-
- Offline
- User
-

Registered
- Posts: 260
- Thanks: 1
Re: Broken bolts...OMG!
12 Mar 2011 03:25
pete@PMH wrote:
I'm with wireman on this one. Remove the cylinder head. Once its on the bench, it'll be a whole lot easier to remove the bolt fragments. Before you do that, source a new head gasket etc that you might need. Sure, it'll take longer, but if you snap off an easy out in there because the angle's wrong or drill something you didn't mean to, you won't be happy. I've learned this one the hard way.
If memory serves, these are 6mm bolts and don't need much torque. When you fit in the new ones, apply a little anti-seize for next time.
hope this helps...Sam
Okay...so whilst removing carb boots from my 650 cylinder head, 3 of the machine screws broke off. After 3 days of soaking them with penetrating oil, drilling right through the remaining stud and testing my 'easy out' tool to the extreme, no luck...any ideas? I'd like to question the term 'EASY'...!
I'm with wireman on this one. Remove the cylinder head. Once its on the bench, it'll be a whole lot easier to remove the bolt fragments. Before you do that, source a new head gasket etc that you might need. Sure, it'll take longer, but if you snap off an easy out in there because the angle's wrong or drill something you didn't mean to, you won't be happy. I've learned this one the hard way.
If memory serves, these are 6mm bolts and don't need much torque. When you fit in the new ones, apply a little anti-seize for next time.
hope this helps...Sam
--
Current Rides: 2013 BMW R1200GSW, 1972 BMW R75/5
Current Project: 1978 KZ1000A2: Supercrank'd by Falicon, APE studs and nuts, Dyna Green coils, powder coated frame and fenders, Stainless brake lines, dual front discs, pods, Kerker Exhaust, 1075cc with JE pistons
Current Rides: 2013 BMW R1200GSW, 1972 BMW R75/5
Current Project: 1978 KZ1000A2: Supercrank'd by Falicon, APE studs and nuts, Dyna Green coils, powder coated frame and fenders, Stainless brake lines, dual front discs, pods, Kerker Exhaust, 1075cc with JE pistons
Please Log in or Create an account to join the conversation.
- testarossa
-
- Offline
- User
-

Registered
- Attack life, it's only trying to kill you.
- Posts: 3673
- Thanks: 83
Re: Broken bolts...OMG!
12 Mar 2011 04:33
If you haven't drilled them out too far, get a left hand drill bit (no I'm not kidding.) You'll have to run your drill in reverse. Use No cutting oil or lubricant on the drill bit. You want it to grab on the screw and the reverse rotation should naturally unscrew the fastener. Don't try and force the easy out, or you will have a worse problem. I agree that the head should probably be off for this procedure. I have removed a lot of broken screws with left hand bits over the years.
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: Broken bolts...OMG!
12 Mar 2011 04:34
Head off and take to machinists... Easiest method.
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Broken bolts...OMG!
12 Mar 2011 04:55
If enough of the remaining stud is accessible, may sometimes tack weld a nut onto the stud (through inside of the nut) and then twist the nut.
Good Fortune!
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- ski1215
-
- Offline
- User
-

Registered
- Posts: 7
- Thanks: 0
Re: Broken bolts...OMG!
12 Mar 2011 05:49
Patton wrote:
Another good method, if you have anything remaining, is to cut a nice deep slot into it and use a flathead screwdriver
If enough of the remaining stud is accessible, may sometimes tack weld a nut onto the stud (through inside of the nut) and then twist the nut.
Good Fortune!
Another good method, if you have anything remaining, is to cut a nice deep slot into it and use a flathead screwdriver
Please Log in or Create an account to join the conversation.
- martin_csr
-
- Offline
- User
-

Registered
- Posts: 7993
- Thanks: 1648
Last edit: 11 Feb 2013 13:25 by martin_csr.
Please Log in or Create an account to join the conversation.
- stonemaster
-
- User
-

Public
- Thanks: 0
Re: Broken bolts...OMG!
12 Mar 2011 07:34
Old Man Rock wrote:
+ 1000 thats what I'd do
Head off and take to machinists... Easiest method.
+ 1000 thats what I'd do
Please Log in or Create an account to join the conversation.
- pete@PMH
-
Topic Author
- Offline
- User
-

Registered
- Posts: 18
- Thanks: 0
Re: Broken bolts...OMG!
12 Mar 2011 07:47
Thanks alot...Im trying to be patient and drilled through the studs so i could fill the whole cavity with liquid wrench..
'79 KZ650C,
Re-Building '78 KZ650B
Re-Building '78 KZ650B
Please Log in or Create an account to join the conversation.
- pete@PMH
-
Topic Author
- Offline
- User
-

Registered
- Posts: 18
- Thanks: 0
Re: Broken bolts...OMG!
12 Mar 2011 07:51
I'm off to get a decent propane torch and give that a try. The head was already off..got it stripped right down.
'79 KZ650C,
Re-Building '78 KZ650B
Re-Building '78 KZ650B
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
