Initial start Please help
- khawk912
-
Topic Author
- Offline
- User
-

Registered
- Posts: 59
- Thanks: 0
Initial start Please help
12 Mar 2011 08:54
hey guys so i got my carbs set put in today and set up a temp gas tank out of a coke bottle. im putting the supply into the bigger hose line and still not getting anything, im getting spark the motor spins nice did i forget to do something?!
Please Log in or Create an account to join the conversation.
- stonemaster
-
- User
-

Public
- Thanks: 0
Re: Initial start Please help
12 Mar 2011 09:31
khawk912 wrote:
ur gas tank is vented, is ur coke bottle ????hey guys so i got my carbs set put in today and set up a temp gas tank out of a coke bottle. im putting the supply into the bigger hose line and still not getting anything, im getting spark the motor spins nice did i forget to do something?!
Please Log in or Create an account to join the conversation.
- khawk912
-
Topic Author
- Offline
- User
-

Registered
- Posts: 59
- Thanks: 0
Re: Initial start Please help
12 Mar 2011 10:06
no, i got it to turn over with some starting fluid then it died maybe the no vent could not let the gas flow to well? either way i tried starting it with no pipes at first and was getting nothing, then my electric start wouldnt do it and had to be done with the kick.
Please Log in or Create an account to join the conversation.
- khawk912
-
Topic Author
- Offline
- User
-

Registered
- Posts: 59
- Thanks: 0
Re: Initial start Please help
12 Mar 2011 11:36
put a vent in the bottle and its not helping i cant get it to start, i have spark it ran with some starting fluid and died
Please Log in or Create an account to join the conversation.
- stonemaster
-
- User
-

Public
- Thanks: 0
Re: Initial start Please help
12 Mar 2011 11:41
then its not getting gas, check carb bowls to see if gas is flowing in them first
Please Log in or Create an account to join the conversation.
- khawk912
-
Topic Author
- Offline
- User
-

Registered
- Posts: 59
- Thanks: 0
Re: Initial start Please help
12 Mar 2011 11:46
yea just checked i think i was actually flooded? a little bit was coming out of the overflow on the bottom of the bowls
Please Log in or Create an account to join the conversation.
- stonemaster
-
- User
-

Public
- Thanks: 0
Please Log in or Create an account to join the conversation.
- Link14
-
- Offline
- User
-

Registered
- Posts: 575
- Thanks: 6
Re: Initial start Please help
12 Mar 2011 12:08
I'm not one of the carb experts here, but I have had these symptoms before. If you are flooding, you are not getting enough of an airgap between the jet and the surface of the gas in the carb bowl and can't atomize the fuel to fire in the engine. Two primary reasons for flooding are float bowl adjustment and the needle valves leaking by. The float adjustment is kind of a pain, but if you are leaking because debris around the needle valve, try opening the drain valves to flush around the needle valve. I also had to give my carb bowls a good tap with a cresent to get things sitted right.
My $0.02
Good Luck
My $0.02
Good Luck
Please Log in or Create an account to join the conversation.
- Proxy
-
- Offline
- User
-

Registered
- 80% Human 20% Nuts/Bolts
- Posts: 510
- Thanks: 46
Re: Initial start Please help
12 Mar 2011 12:33
khawk912 wrote:
The bigger hose line? You are not talking about the carb vent(s) are you? I'm not understanding when you say the bigger hose line.
im putting the supply into the bigger hose line and still not getting anything, im getting spark the motor spins nice did i forget to do something?!
The bigger hose line? You are not talking about the carb vent(s) are you? I'm not understanding when you say the bigger hose line.
Take it from me cuz I found
If you leave it then somebody else is bound,
To find that treasure, that moment of pleasure,
When yours, it could have been.
1977 KZ650 B1 Being restored to original (Green)
1977 KZ650 B1 Original (Red) Sold
1977 KZ650 B1 Donor Bike for Parts
If you leave it then somebody else is bound,
To find that treasure, that moment of pleasure,
When yours, it could have been.
1977 KZ650 B1 Being restored to original (Green)
1977 KZ650 B1 Original (Red) Sold
1977 KZ650 B1 Donor Bike for Parts
Please Log in or Create an account to join the conversation.
- khawk912
-
Topic Author
- Offline
- User
-

Registered
- Posts: 59
- Thanks: 0
Re: Initial start Please help
12 Mar 2011 12:57
theres two lines that go to the petcock im hooking it up to the bigger one
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: Initial start Please help
12 Mar 2011 14:26 - 12 Mar 2011 14:27
You must remove your carbs again and clean them properly.
Sorry, but its the only/proper way.
Either the floats are set improperly, or the float valves are leaking fuel past them.
Filling the carbs with fuel for the first time, should be done on the bench with a gravity feed tank (of any kind) that is vented. You can get a real cheap gas tank with shutoff valve from a lawnmower recycler.
Remove you float valve needles and inspect them. If they are rubber tipped, they can sometimes be gently scraped clean with a stiff plastic knife/tool. If they are metal, and they dont have a sever groove, they can be polished.
Put them in a drill and spin them against a cloth with some metal polish on it. Repeat unitl no noticable groove is visible.
The valve seats need to be polished as well. Insert a cotton swab into your drill. Dip it in some polish and then spin polish the seat with the swab. Make them nice and shiney clean.
When done everything else - (setting floats, cleaning jets, visually verifying the fuel flow through jet passages, etc), setup your carbs in a vice/block so that they can stand up fine while you fill them with fuel. If the valves still leak, then they will need more attention or replacement.
I test petcocks in the sameway - off the bike, to prevent flooding and fouling of the engine oil.
Once filled with gas, if they are holding fine, you will be able to perform the fuel height testing. They should be able to hold fuel overnight.
Good luck!
Now MFolks can post his carb cleaning 101/2 :laugh:
Sorry, but its the only/proper way.
Either the floats are set improperly, or the float valves are leaking fuel past them.
Filling the carbs with fuel for the first time, should be done on the bench with a gravity feed tank (of any kind) that is vented. You can get a real cheap gas tank with shutoff valve from a lawnmower recycler.
Remove you float valve needles and inspect them. If they are rubber tipped, they can sometimes be gently scraped clean with a stiff plastic knife/tool. If they are metal, and they dont have a sever groove, they can be polished.
Put them in a drill and spin them against a cloth with some metal polish on it. Repeat unitl no noticable groove is visible.
The valve seats need to be polished as well. Insert a cotton swab into your drill. Dip it in some polish and then spin polish the seat with the swab. Make them nice and shiney clean.
When done everything else - (setting floats, cleaning jets, visually verifying the fuel flow through jet passages, etc), setup your carbs in a vice/block so that they can stand up fine while you fill them with fuel. If the valves still leak, then they will need more attention or replacement.
I test petcocks in the sameway - off the bike, to prevent flooding and fouling of the engine oil.
Once filled with gas, if they are holding fine, you will be able to perform the fuel height testing. They should be able to hold fuel overnight.
Good luck!
Now MFolks can post his carb cleaning 101/2 :laugh:
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Last edit: 12 Mar 2011 14:27 by TeK9iNe.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
