valve cover end caps

  • stonemaster
  • stonemaster's Avatar Topic Author
  • User
  • User
    Public
  • Thanks: 0

valve cover end caps

14 Mar 2011 20:11
#438025
started motor for first time and two of the valve cover end caps blew out, I couldnt find the aluminum ones i had and used some rubber ones, this happen much ??? I think I read somewhere this was an issue with those,

Please Log in or Create an account to join the conversation.

  • APE Jay
  • APE Jay's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: valve cover end caps

14 Mar 2011 20:49
#438032
Crankcase pressure will do that. Some rcers used to put them in backwards to prevent that. Of course, that is all now a thing of the past.



kzzone.com/plugs.html

Please Log in or Create an account to join the conversation.

  • testarossa
  • testarossa's Avatar
  • Offline
  • User
  • User
    Registered
  • Attack life, it's only trying to kill you.
  • Posts: 3673
  • Thanks: 83

Re: valve cover end caps

14 Mar 2011 20:52
#438035
I had one that worked it's way out twice. Now I currently have one that is trying to crawl inside the head. I installed them with a very thin coating of Yamabond 4. I'm due for a vavle clearance check so hopefully I can get the problematic one stuck down this time.
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN

Please Log in or Create an account to join the conversation.

  • stonemaster
  • stonemaster's Avatar Topic Author
  • User
  • User
    Public
  • Thanks: 0

Re: valve cover end caps

14 Mar 2011 20:59
#438036
I got some aluminum from Z1 Ent ordered, they got a slot for a thin rubber gasket, cool
I found some more info on this issue a few minutes ago, seems some even got sucked in ???:ohmy:

Please Log in or Create an account to join the conversation.

  • stonemaster
  • stonemaster's Avatar Topic Author
  • User
  • User
    Public
  • Thanks: 0

Re: valve cover end caps

14 Mar 2011 21:00
#438039
APE Jay wrote:
Crankcase pressure will do that. Some rcers used to put them in backwards to prevent that. Of course, that is all now a thing of the past.



kzzone.com/plugs.html

nice except for the fact they're blue thanx man

Please Log in or Create an account to join the conversation.

  • stonemaster
  • stonemaster's Avatar Topic Author
  • User
  • User
    Public
  • Thanks: 0

Re: valve cover end caps

14 Mar 2011 21:03 - 14 Mar 2011 21:05
#438042
testarossa wrote:
I had one that worked it's way out twice. Now I currently have one that is trying to crawl inside the head. I installed them with a very thin coating of Yamabond 4. I'm due for a vavle clearance check so hopefully I can get the problematic one stuck down this time.
damn dude I'd go for the aluminum, the ones apej shows even match ur bike :huh:
Last edit: 14 Mar 2011 21:05 by stonemaster.

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: valve cover end caps

14 Mar 2011 22:44 - 14 Mar 2011 22:48
#438069
stonemaster wrote:
started motor for first time and two of the valve cover end caps blew out, I couldnt find the aluminum ones i had and used some rubber ones, this happen much ??? I think I read somewhere this was an issue with those,
It can't happen if they are properly installed. I should post a sticky on it, I have put it up several times. The head surface has to be scraped clean and stripped dry with acetone. Use a good sealant and do a partial torque leaving a little rubber above the head surface. let the bond agent fully cure then torque. The reason most blow out is they are installed and torqued when the sealer is wet which squeezes all of it out.

Aluminum ones are better if they make them for your engine.
1979 KZ-750 Twin
Last edit: 14 Mar 2011 22:48 by bountyhunter.

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: valve cover end caps

14 Mar 2011 22:48
#438070
stonemaster wrote:
started motor for first time and two of the valve cover end caps blew out, I couldnt find the aluminum ones i had and used some rubber ones, this happen much ??? I think I read somewhere this was an issue with those,
clean em up with acetone,glue them in and let em dry B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • larrycavan
  • larrycavan's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: valve cover end caps

15 Mar 2011 03:22
#438090
stonemaster wrote:
APE Jay wrote:
Crankcase pressure will do that. Some rcers used to put them in backwards to prevent that. Of course, that is all now a thing of the past.



kzzone.com/plugs.html

nice except for the fact they're blue thanx man

That blue can be removed.

Please Log in or Create an account to join the conversation.

  • larrycavan
  • larrycavan's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: valve cover end caps

15 Mar 2011 03:24 - 15 Mar 2011 03:24
#438091
wireman wrote:
stonemaster wrote:
started motor for first time and two of the valve cover end caps blew out, I couldnt find the aluminum ones i had and used some rubber ones, this happen much ??? I think I read somewhere this was an issue with those,
clean em up with acetone,glue them in and let em dry B)

Put them on the workbench vise, get a 3lb hammer and send them to cam end plug heaven :woohoo: ... JMO
Last edit: 15 Mar 2011 03:24 by larrycavan.

Please Log in or Create an account to join the conversation.

  • stonemaster
  • stonemaster's Avatar Topic Author
  • User
  • User
    Public
  • Thanks: 0

Re: valve cover end caps

15 Mar 2011 04:27
#438099
larrycavan wrote:
wireman wrote:
stonemaster wrote:
started motor for first time and two of the valve cover end caps blew out, I couldnt find the aluminum ones i had and used some rubber ones, this happen much ??? I think I read somewhere this was an issue with those,
clean em up with acetone,glue them in and let em dry B)

Put them on the workbench vise, get a 3lb hammer and send them to cam end plug heaven :woohoo: ... JMO
agreed, POS IMO

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: valve cover end caps

15 Mar 2011 08:46
#438129
those simple little stock pieces last for years and go many 1000s of miles in a lot of bikes without issues! :laugh:
ill add those billet beutys to list of things to stock just for you 2! :laugh:
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum