t. k. carb ?
- allen6634
-
Topic Author
- Offline
- User
-

Registered
- Posts: 48
- Thanks: 0
t. k. carb ?
19 Mar 2011 06:09
after all the work i have been doing i talked to my budy , he is the guy who did my carbs in the first place , he is thinking that he put the slides in backwards , my question is , how do i know or find out the orietation of the slides on my carbs?
1983 kz 550 m
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: t. k. carb ?
19 Mar 2011 11:15 - 19 Mar 2011 11:15
the high side of the slides bottom taper faces the back of the bike. i dought u could put them in backwards. they should only fit 1 way.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Last edit: 19 Mar 2011 11:15 by mark1122.
The following user(s) said Thank You: allen6634
Please Log in or Create an account to join the conversation.
- stonemaster
-
- User
-

Public
- Thanks: 0
Re: t. k. carb ?
19 Mar 2011 11:22 - 19 Mar 2011 11:26+1 on thatmark1122 wrote: the high side of the slides bottom taper faces the back of the bike. i dought u could put them in backwards. they should only fit 1 way.
I've never messed with that brand of carb HOWEVER based on what u've said i would be suspect of your buddies skill, I think its time to drop back and punt, get the diagrams and specs for ur carb and start over, disassemble and make sure everything is as its supposed to b, the reassemble, that way YOU will know its right instead chasing gremlins JMO
I've had "buddies" tell me things before who were supposed to know what they were talking about, NEVER TRUST EM, I had one tell me about cam bearing scratches and the like and he was full of it. I now only ask advice from genuine experts, and be advised even they can be wrong sometimes
Last edit: 19 Mar 2011 11:26 by stonemaster.
Please Log in or Create an account to join the conversation.
- newOld_kz1000
-
- Offline
- User
-

Registered
- FlimFlamFlibbityFlee !! BoonFryedShickaMuhZee !!
- Posts: 751
- Thanks: 20
Re: t. k. carb ?
19 Mar 2011 13:46
I have a Kaw triple (400cc triple) and you can definitely put the slides in backward.
I have never dealt with T-K carbs, I know that on most Mics the slides only fit one way
on 4 stroke fours I've dealt with (on the stock carbs at least) but if you're concerned,
there's an easy way to check:
Ignore the comment on the photo about the thumbwheel and look at the gap between the bottom of the throttle slide and the carb throat -- each carb has such a gap. Some carb slides have an arc cut out of the bottom of the slide (my Kaw triple has such arc'd cutouts on its carb slides) and some carbs, these for example from my 1981 kz650 have a gap but not as pronounced of any arc.
On my triple's carbs, when I installed the slides backward, that gap *disappears* and it's easy to check.
My 400 ran kinda bad once after a carb job. I popped off the stock airbox to get it out of the way and used a small mirror (hard to look directly into the back of the carbs when they're on the bike, mirror helped me here). I found that my center carb had no gap between the bottom of its throttle slide and the carb throat.
On your TK carbs maybe you can do that, and check to verify that when the throttle's all the way closed, you have the exact same gap on each carb between the bottom of the slide and carb throat.
If TK carbs do allow 'backward' installation of the throttle slide, you *might* use this technique to detect that condition. I used it to solve my poor running situation on my 400 Kaw triple; I pulled the carb slide and rotated it 180 degrees, bike ran great afterward.
Good luck.
I have never dealt with T-K carbs, I know that on most Mics the slides only fit one way
on 4 stroke fours I've dealt with (on the stock carbs at least) but if you're concerned,
there's an easy way to check:
Ignore the comment on the photo about the thumbwheel and look at the gap between the bottom of the throttle slide and the carb throat -- each carb has such a gap. Some carb slides have an arc cut out of the bottom of the slide (my Kaw triple has such arc'd cutouts on its carb slides) and some carbs, these for example from my 1981 kz650 have a gap but not as pronounced of any arc.
On my triple's carbs, when I installed the slides backward, that gap *disappears* and it's easy to check.
My 400 ran kinda bad once after a carb job. I popped off the stock airbox to get it out of the way and used a small mirror (hard to look directly into the back of the carbs when they're on the bike, mirror helped me here). I found that my center carb had no gap between the bottom of its throttle slide and the carb throat.
On your TK carbs maybe you can do that, and check to verify that when the throttle's all the way closed, you have the exact same gap on each carb between the bottom of the slide and carb throat.
If TK carbs do allow 'backward' installation of the throttle slide, you *might* use this technique to detect that condition. I used it to solve my poor running situation on my 400 Kaw triple; I pulled the carb slide and rotated it 180 degrees, bike ran great afterward.
Good luck.
1978 kz1000 A2 with Kerker
1980 Z1 Classic with Kerker
1980 Z1 Classic with Kerker
The following user(s) said Thank You: allen6634
Please Log in or Create an account to join the conversation.
- loudhvx
-
- Offline
- KZr Legend
-

Registered
- Posts: 10863
- Thanks: 1622
Re: t. k. carb ?
19 Mar 2011 14:10 - 19 Mar 2011 14:12
The TK-22 slide has a groove which prevents installation errors.
The KZ550M uses TK-26 CV's. I believe they also have the groove.
The KZ550M uses TK-26 CV's. I believe they also have the groove.
1981 KZ550 D1 gpz.
Kz550 valve train warning.
Other links.
Kz550 valve train warning.
Other links.
Last edit: 19 Mar 2011 14:12 by loudhvx.
The following user(s) said Thank You: allen6634
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
