oil pump noise

  • nads.com
  • nads.com's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 993
  • Thanks: 20

oil pump noise

20 Mar 2011 06:05 - 20 Mar 2011 06:18
#439110
I cleaned up the oil pump and it makes a clicking noise as I spin the sprocket on it.

Took one from a diff engine and it doesn't click

I took the clicker apart and didn't find anything (no I did not measure the gear lash)
cuz that wont tell me why it clicks.

so I'm using the silent one

I knew I would have oil pump problems

So here put it together and it binds

Never messed with it so I don't know if it needs the two gears alighned or what.

Maybe the holes in the pump case are loose?

Just wonder if anyone one knows anything

I know that I'm getting old

This forum is slow to change pages

Should never have looke at that porn.

But what about my pump?

Dave?

I know you had problems

What's going on here man, scoop me

I'm lost inside my pump and need direction.

I can't use it or sell it like that

One time last summer I was riding and the motor starting to tick pretty good

I think I was low on oil

I left the filler plug out

or was that another time?

see I'm getting old and can't think

So I need to bypass the memory stuff

It's worthless

Oil pump 101 is where I'm at now.

I sprayed the clicker with carb clean and maybe that's why it clicks, too clean inside

I washed the other with dawn

Maybe I'll spray down the anticlicker and see if it clicks

I think kz oil pump road could easily merge with virago starter gear road (add meth)

Never let anyone pay you in white, and never work on a virago

People Don't think your normal when u can't stop playing with the gears in the living room of the neigbors house

They think it still has grease on it

how can people be so unknowing, unobservant?
Last edit: 20 Mar 2011 06:18 by nads.com.

Please Log in or Create an account to join the conversation.

  • Old Man Rock
  • Old Man Rock's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6071
  • Thanks: 225

Re: oil pump noise

20 Mar 2011 12:14
#439138
Maybe I missed it but you didn't mention your oil pressure measurements, up to spec?

As in my case, I was witnessing a weird intermittent engine sound "Squishing"... Out with the stethoscope, traced it all the way down to the oil pump area. :blink:



I opened up the oil pump and found the two gear shafts on the wobbly side. In performing the Gear clearance measurements I found them close to maximum. Time to replace oil pump was the answer... I did research to see if I could just get replacement gears, nope, NADA, not going to happen..

Found an Oil Pump on E-bay for $20 plus shipping. Have had no Squishing issues since... So for the price, just replace the whole damn thing.

As for the ticking, possibly some junk/old RTV pieces, metal pieces etc... are trapped in the oil pump passage...


OMR
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter

Phoenix, Az

Please Log in or Create an account to join the conversation.

  • stonemaster
  • stonemaster's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: oil pump noise

20 Mar 2011 12:23
#439141
nice bike old man :laugh:

Please Log in or Create an account to join the conversation.

  • nads.com
  • nads.com's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 993
  • Thanks: 20

Re: oil pump noise

20 Mar 2011 17:12
#439217
Old Man Rock wrote: Maybe I missed it but you didn't mention your oil pressure measurements, up to spec?

As in my case, I was witnessing a weird intermittent engine sound "Squishing"... Out with the stethoscope, traced it all the way down to the oil pump area. :blink:



I opened up the oil pump and found the two gear shafts on the wobbly side. In performing the Gear clearance measurements I found them close to maximum. Time to replace oil pump was the answer... I did research to see if I could just get replacement gears, nope, NADA, not going to happen..

Found an Oil Pump on E-bay for $20 plus shipping. Have had no Squishing issues since... So for the price, just replace the whole damn thing.

The spare pump I have is very smooth so I'll use it.

I never checked the old pump for wobble, but it's probly worn out the same as yours. I suspected the case bores to be the prob.

Maybe running the bike for 3years without air filters and dirty oil......

How did the ebay pump spec compared to the worn pump?

Thanks for the insight! I'm comfortable with info from someone who doesn't make a move until it's clear.






As for the ticking, possibly some junk/old RTV pieces, metal pieces etc... are trapped in the oil pump passage...


OMR

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: oil pump noise

20 Mar 2011 19:11
#439242
just check the gear clearance , it is likely out of spec.. the clickee may be from being dryee.
all u can do is buy from ebay and hope u get 1 in spec. i was able to make 1 out of 2 and got a good spec.
also check the clearance between the lid and gear with plastigauge. u can use a thinner gasket to pick up added presure.
is this for a z1/kz ?
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • nads.com
  • nads.com's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 993
  • Thanks: 20

Re: oil pump noise

21 Mar 2011 00:59
#439324
mark1122 wrote: just check the gear clearance , it is likely out of spec.. the clickee may be from being dryee.
all u can do is buy from ebay and hope u get 1 in spec. i was able to make 1 out of 2 and got a good spec.
also check the clearance between the lid and gear with plastigauge. u can use a thinner gasket to pick up added presure.
is this for a z1/kz ?

It's for a 76 kz .... How can a thinner gasket make more pressure? And do I really need it?

Please Log in or Create an account to join the conversation.

  • nads.com
  • nads.com's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 993
  • Thanks: 20

Re: oil pump noise

21 Mar 2011 01:02
#439325
mark1122 wrote: just check the gear clearance , it is likely out of spec.. the clickee may be from being dryee.
all u can do is buy from ebay and hope u get 1 in spec. i was able to make 1 out of 2 and got a good spec.
also check the clearance between the lid and gear with plastigauge. u can use a thinner gasket to pick up added presure.
is this for a z1/kz ?

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: oil pump noise

21 Mar 2011 01:04
#439326
i like the fast by grump cam plugs! :woohoo:
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • testarossa
  • testarossa's Avatar
  • Offline
  • User
  • User
    Registered
  • Attack life, it's only trying to kill you.
  • Posts: 3673
  • Thanks: 83

Re: oil pump noise

21 Mar 2011 02:27
#439344
My oil pumps,a clickin'
My Timex, quit tickin'
My fryin' pan's a stickin'
Whatever should I do?

OMR's got a plan,
throw the pump in the can.
Move along in a van
It's not hard to do..

Dave's got it figured out,
you're oil pump has the gout.
Ebay has the answer,
paypal is the cure.

Just give us you're PIN
the oil pump will come in
Fat lady rides again.
nads, the hero, claims a win
this much is true...

I've given it my all,
Testarossa must fall,
Diesel engine's my call
Kerosene lights the hall
and the time's worth it all...
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN

Please Log in or Create an account to join the conversation.

  • Old Man Rock
  • Old Man Rock's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6071
  • Thanks: 225

Re: oil pump noise

21 Mar 2011 05:47
#439364
Wholly Crapola... :laugh: :laugh: :laugh:
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter

Phoenix, Az

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: oil pump noise

21 Mar 2011 05:58
#439365
Old Man Rock wrote: Wholly Crapola... :laugh: :laugh: :laugh:

That almost rhymes! :cheer:
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • Old Man Rock
  • Old Man Rock's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6071
  • Thanks: 225

Re: oil pump noise

21 Mar 2011 06:11
#439366
@ 2am you want rhymes?

Humpty Dumpty sat on a wall...
Old fart Patton is busting old man rocks balls.... :P :laugh:
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter

Phoenix, Az

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum