80 KZ1000ST from a crackhead

  • dkshadow
  • dkshadow's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 12
  • Thanks: 0

80 KZ1000ST from a crackhead

22 Mar 2011 21:58
#439808
I just picked up a 80 KZ1000ST from a guy at work (he is known as the shop crackhead) for $200 and now I have to fix all the dumb stuff he did to it. Now with that said, it runs on #1 and #4 with no spark on #2 and #3. The coil on that side was cracked wide open so I replaced it with one off eBay and still no spark. Before I go buy new coils any thing I should test? The weather is warming up here and I sold my Hondas to fund fixing this one cuz my buddy has the identical bike and he loves his and I've rode it and it's sweet.
Ride Till You Rot

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: 80 KZ1000ST from a crackhead

22 Mar 2011 23:58
#439835
Try these tests:

Ignition Coil Primary And Secondary Wiring

Ignition coils on the 80’s Kz1000,Kz1100’s and Gpz1100’s are wired the same, that is as you sit on the bike, the LEFT ignition coil primary(small wires) are two wires, RED and BLACK. The secondary (or sparkplug wires) go to #1 and #4 sparkplugs(your primary wiring may be different).

The cylinders are numbered left to right as you sit on the seat; #1,#2,#3, and #4.

For the RIGHT ignition coil, the primary wires, again are two wires, RED and GREEN, with the secondary going to #2 and #3.

The RED wire gets it’s voltage from the run/stop switch on the right handlebar switch pod.Your coil wiring may have RED with YELLOW stripe.

The BLACK and GREEN wires connect to the IC Igniter(if the bike has the Kawasaki supplied electronic ignition) it actually gives the coils their grounds to fire the sparkplugs.

Primary(small wires) side of the coils will read between 1.8 to 3.0 ohms.

Secondary(sparkplug wire ports)side of the coil will read between 10.4K to 15.6K ohms. These ports are wired together, so it makes no difference which is used, as long as the correct coil to sparkplug configuration is followed.

The sparkplug caps should read 5K OHMS, any higher, or a reading of infinity means new caps should be ordered.

To stress the ignition coils, take a hair dryer, heat the coils and see if the ohm readings change from cold to hot . If they do, it’s time to buy new coils.

Keep in mind, the wiring is reversed for the 550’s 650‘s and 750‘s, that is the RIGHT coil primary will be two wires, RED and BLACK with the secondary(sparkplugs) going to #1 and #4.

The LEFT coils primary wiring would be again two wires, RED and GREEN, with the secondary(sparkplugs) going to #2 and #3.

These engines have what is known as a “Wasted Spark” that is, a sparkplug will fire during an exhaust stroke. It does no damage and many other motorcycle engines have this design.
_________________________________________________________________________________________________
And:

Ohm Checking Pickup(Pulsing) Coils

The pickup coils on the Kawasaki’s with the factory supplied electronic ignition can sometimes fail or become intermittent due to heat and vibration.

1.Trace back from where the pick up coils are mounted,(under a right side CD sized cover) locate and disconnect a small 4 pin connector. Using a multi-meter set on OHMS and range of 2K, check between the BLUE and BLACK wires(#1 and #4 sparkplug wires) for between 360- 540 OHMS.

2.For #2 and #3 sparkplugs the wire colors will be YELLOW and RED, again 360-540 OHMS.

3.If the pickup coils are suspect of failing due to heat, they can be stressed using a hair dryer without the need of the engine running.

4.A replacement set of pickup coils might be obtained from a dealer who serviced the police Kawasaki’s.

5. If replacement pickup coils are not available, your next choice would be to order a Dyna “S” electronic ignition system from www.z1enterprises.com It replaces the IC igniter with a smaller module located where the mechanical ignition advancer was mounted.

6. Checking with Kawasaki.com website has determined that the Pick up(pulsing) coils are available . The pulsing coil # is 59026-1133 and replaces the older # 1002, 1012 which were used from the MKII motors until the 2005 P24.

7.Check the small 4 pin connector that the pickup coils connect to for corrosion/loose pins too.

The ignition coils and sparkplug caps and wires are probably overdue for replacement. Even when new the ignition coils were marginal in spark output. I'd get a multimeter and check the primary resistance to see what ohm range you'll need.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
The following user(s) said Thank You: kzrider, dkshadow

Please Log in or Create an account to join the conversation.

  • dkshadow
  • dkshadow's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 12
  • Thanks: 0

Re: 80 KZ1000ST from a crackhead

23 Mar 2011 23:02
#440029
wow I was hoping for an easy answer I'll have to wait till this weekend to check that stuff if I can figure it all out but thanks for some Ideas
Ride Till You Rot

Please Log in or Create an account to join the conversation.

  • dkshadow
  • dkshadow's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 12
  • Thanks: 0

Re: 80 KZ1000ST from a crackhead

23 Mar 2011 23:10
#440035
ok I talked to the guy I got it from and he said it was an intermittent thing at first then finally went out. the plug wires are definitely shot the boots keep falling off so im going to buy new coils and wires ether way and sounds like a new cap would be a good idea too.
Ride Till You Rot

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: 80 KZ1000ST from a crackhead

23 Mar 2011 23:18
#440040
www.z1enterprises.com sells Dyna ignition coils,sparkplug wires, both resistive and non resistive some what cheaper than Dyna does on their website.

For a stronger spark(but your friends may not like the elctrical noise)go with the Dyna copper sparkplug wires with the molded on caps.

Check your old coils(if possible) to see what resistance they are. Use a multimeter with the primary (small wires) side to determine if what you'll need is 3 ohm or less.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • dkshadow
  • dkshadow's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 12
  • Thanks: 0

Re: 80 KZ1000ST from a crackhead

29 Mar 2011 19:29
#441274
Ok new coils and wires caps all the good stuff. I checked the ohms coming from the pickups and get 439ohms from black and blue but nothing from yellow and red.I take it I need new pickup coils?..
Ride Till You Rot

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: 80 KZ1000ST from a crackhead

29 Mar 2011 19:40
#441277
I'd replace both(I believe they come as a set). Or go with a Dyna "S" igntion as a complete replacement. Check with www.z1enterprises.com first about the pick up coils before spending $$ for a Dyna.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: 80 KZ1000ST from a crackhead

29 Mar 2011 21:52
#441319
dkshadow wrote: ...80 KZ1000ST...runs on #1 and #4 with no spark on #2 and #3....

Could test 3 o'clock pick-up module by moving 2/3 trigger wire to 1/4 coil, and visually observe whether 1/4 plugs still spark while spinning over the engine, which would indicate that 3 o'clock pick-up module is okay.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • dkshadow
  • dkshadow's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 12
  • Thanks: 0

Re: 80 KZ1000ST from a crackhead

30 Mar 2011 17:02
#441455
I did change the wires around like that but I didn't visually observe it I held an allen wrench in the my hand and in the cap, it zapped me good and I liked it, lol.
Ride Till You Rot

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: 80 KZ1000ST from a crackhead

30 Mar 2011 18:28
#441467
dkshadow wrote: I did change the wires around like that but I didn't visually observe it I held an allen wrench in the my hand and in the cap, it zapped me good and I liked it, lol.

Hope it was a good fat blue zap and not a wimpy weak orange zap. :lol:

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • dkshadow
  • dkshadow's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 12
  • Thanks: 0

Re: 80 KZ1000ST from a crackhead

31 Mar 2011 17:38
#441733
looking at some pulse coils on eBay off a 83 KZ1000, they look the same, dose anybody know if there would work?
Ride Till You Rot

Please Log in or Create an account to join the conversation.

  • purls
  • purls's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 91
  • Thanks: 0

Re: 80 KZ1000ST from a crackhead

01 Apr 2011 01:18 - 01 Apr 2011 01:20
#441851
Don't mean to beat a dead horse, but MFolks is right. Dyna S ignition or Dyna coils, at least. With so much to think about already, Dyna was a no-brainer for me. And, since I'm pretty much a no-brainer myself... well, you see where I'm going.

Good luck
1983 KZ750 Spectre
1978 KZ650B2A
Last edit: 01 Apr 2011 01:20 by purls.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum