Ignition Assembly

  • veritas.wilson
  • veritas.wilson's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 12
  • Thanks: 0

Ignition Assembly

24 Mar 2011 19:24
#440192
I took the ignition cap off my 83 kz550 and found a large amount of corrosion. does anyone have any advice on how to deal with this problem and if i need to replace the ignition system ?

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Ignition Assembly

24 Mar 2011 19:38
#440198
veritas.wilson wrote: I took the ignition cap off my 83 kz550 and found a large amount of corrosion. does anyone have any advice on how to deal with this problem and if i need to replace the ignition system ?

Dyna-S ignition, Dyna 3 ohm green coils, and Dyna 7mm solid core plug wires.

Click > www.z1enterprises.com/detail.aspx?ID=201

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • veritas.wilson
  • veritas.wilson's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 12
  • Thanks: 0

Re: Ignition Assembly

24 Mar 2011 21:18
#440216
so its safe to assume the ignition is shot or just needs replaced ? im almost done cleaning the head/replacing gaskets to see if it actually runs, could it wait till after i find out if the engine is shot ?
thanks for the help
sean

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Ignition Assembly

25 Mar 2011 00:32
#440282
veritas.wilson wrote: so its safe to assume the ignition is shot or just needs replaced ? im almost done cleaning the head/replacing gaskets to see if it actually runs, could it wait till after i find out if the engine is shot ? thanks for the help
sean

Won't hurt to try. :cheer:

Could reassemble the existing ignition, after carefully cleaning the area in pick-up modules where the rotor passes.
From the pic, it's impossible to see whether the wiring is intact.
And maybe the ic igniter remains serviceable, along with the ignition coils.

What's running history of the bike?
How long stored?
Is a FSM at hand?

Ultimate goal for the ignition system is a healthy and properly timed spark on each plug.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • veritas.wilson
  • veritas.wilson's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 12
  • Thanks: 0

Re: Ignition Assembly

25 Mar 2011 15:05
#440366
i see the term "garage find" alot, this bike is more of a "back yard under a torn up tarp" find.
best i can figure out is it hasnt run in at least 6 years. no one has touched it in that long
either. when i got it, all the guy knew was that the guy he got it from said bad head gasket and the
"wiring was shot."
Although it wasnt taken care of very well, the only major problem ive seen so far is the ignition assembly. and i have a feeling im going to be fiddling around with the wiring for a while
is the fms the repair manual ? because i wouldnt have been brave enough to take the head off with out it :cheer:

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Ignition Assembly

25 Mar 2011 16:04
#440369
FSM refers to Factory Service Manual, and sometimes Factory Shop Manual.

The wiring diagram will be very helpful.
Click > www.kzrider.com/filebase/doc_download/307-z550h2

Ignition components are powered from the battery.
They include the battery, 2 coils, pickup modules, igniter, and spark plugs.

For the engine to run, requires only ignition components and related wiring to provide good properly timed sparks.

Charging system components aren't needed for the engine to run.
They include the alternator, rectifier, and voltage regulator.
Without them, the engine will perform normally until the battery runs down.

In other words, the ignition relies on power from the battery and couldn't care less how it stays charged.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • veritas.wilson
  • veritas.wilson's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 12
  • Thanks: 0

Re: Ignition Assembly

25 Mar 2011 17:54
#440406
well that is a big help, wiring in not my strong suite.

i am having a hell of a time calling back and forth from part stores including z1enterprises
trying to figure out gasket sets. although im not entirely sure what model i have
on the engine it says kz550 F although every website and person i talk to asks if its an f1 or f2
and some ask if its a spectre... Its a shaft drive kz550 f would you know what model that is ?

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Ignition Assembly

25 Mar 2011 19:14
#440418
1983 KZ550 models:
M1 LTD shaft
F1 Spectre shaft
A4 chain
C4 chain
H2 GPZ chain

The shafty would have started life as either M1 or F1 (basically same drive trains).

F2 is the 1984 model Spectre shaft.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Ignition Assembly

25 Mar 2011 19:22
#440419
Lots of good info on kawasaki.com, including parts diagrams, part numbers, models sharing same part, availability, etc.

Here's a link for help with navigating the site and finding information.

kzrider.com/index.php?option=com_kunena&...w&catid=13&id=376734

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Ignition Assembly

25 Mar 2011 19:24
#440420
Ohm Checking Pickup(Pulsing) Coils

The pickup coils on the Kawasaki’s with the factory supplied electronic ignition can sometimes fail or become intermittent due to heat and vibration.

1.Trace back from where the pick up coils are mounted,(under a right side CD sized cover) locate and disconnect a small 4 pin connector. Using a multi-meter set on OHMS and range of 2K, check between the BLUE and BLACK wires(#1 and #4 sparkplug wires) for between 360- 540 OHMS.

2.For #2 and #3 sparkplugs the wire colors will be YELLOW and RED, again 360-540 OHMS. The 550’s,650’s & 750’s may be backwards to the Z1’s,Kz900’s,Kz1000’s & Kz1100’s.

3.If the pickup coils are suspect of failing due to heat, they can be stressed using a hair dryer without the need of the engine running.

4.A replacement set of pickup coils might be obtained from a dealer who serviced the police Kawasaki’s.

5. If replacement pickup coils are not available, your next choice would be to order a Dyna “S” electronic ignition system from www.z1enterprises.com It replaces the IC igniter with a smaller module located where the mechanical ignition advancer was mounted.

6. Checking with Kawasaki.com website has determined that the Pick up(pulsing) coils are available . The pulsing coil # is 59026-1133 and replaces the older # 1002, 1012 which were used from the MKII motors until the 2005 P24.

7.Check the small 4 pin connector that the pickup coils connect to for corrosion/loose pins too.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum