Jetting questions

  • andy9802gt
  • andy9802gt's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Jetting questions

01 Apr 2011 18:47
#441996
Alright I just put my 1075 back together with a stage one head from Larry C that flows 91cfm at .400, APE superflow filters and RS34's, and a Star Pro Pipe. It was running fine when I seated the rings (I had the idle set @2000) but when I got it out today to start tuning it below 1/4 throttle it wouldn't run without the choke on. It came stock with 17.5 pilots and 125 mains, fuel screws 1 turn out. Do you guys think this is to lean? I was also wondering are these carbs supposed to be synced from the factory or do I have to do it? Just trying to get a good starting point from someone with a similar setup so I don't have to spend a bunch of time tweaking this pig because I'm itching to ride it.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: Jetting questions

01 Apr 2011 18:49
#441998
And those k410 cams lope like a big block at about 900rpms. :evil:
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Jetting questions

01 Apr 2011 19:13
#442000
Syncing the carbs has more to do with your bike than the carbs themselves, so I would go ahead and sync them. You're matching them to the pressure differences between cylinders on your bike when you sync them.

Please Log in or Create an account to join the conversation.

  • testarossa
  • testarossa's Avatar
  • Offline
  • User
  • User
    Registered
  • Attack life, it's only trying to kill you.
  • Posts: 3673
  • Thanks: 83

Re: Jetting questions

01 Apr 2011 20:20
#442013
I'm with DD. Vacuum sync the carbs, adjust the mixture screws for the highest idle, then re-set your idle back to 900-1000. Once you do that, if it still won't run without the choke, then it's time to step up a pilot jet size. Did you check your valve clearances after you assembled the engine? I can't remember from your build thread.
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: Jetting questions

02 Apr 2011 03:47
#442116
Alright, sync the carbs it is. I also ordered 22.5 pilots. Testa, I already took the fuel screws out to three turns and it didn't help much and the valves were set at .005-.006 when I put it together. We've got rain forcast almost everyday this week and the jets won't be in until mid week. Next question is what do you guys use to remove the blueing on your exhaust?
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • larrycavan
  • larrycavan's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Jetting questions

02 Apr 2011 10:20
#442129
First.. I hope you ran it a while to break in the cams before you tried to idle it at 900 RPM...

Second, Don't try to idle it at 900 RPM... Bump that idle up to 1200 RPM. You want the top end to get oil up there.

Third, put in the new pilots [I would have went with #20] start with pilot fuel screws back to 1 turn, adjust as needed.

RIDE THE BIKE... put some miles on it, then worry about carb synch. Let the valves settle in to where they are happy, make sure the ignition timing is dead nuts on, then carb synch.

Don't back that center lock screw off much. The main slide adjuster is super touchy. The closer you get the synch, the less the slides will clack ;)

Where are the lobe centers?

Please Log in or Create an account to join the conversation.

  • TeK9iNe
  • TeK9iNe's Avatar
  • Offline
  • User
  • User
    Registered
  • What did you do!?!
  • Posts: 2436
  • Thanks: 28

Re: Jetting questions

02 Apr 2011 10:24 - 02 Apr 2011 10:24
#442130
larrycavan wrote: First.. I hope you ran it a while to break in the cams before you tried to idle it at 900 RPM...

Second, Don't try to idle it at 900 RPM... Bump that idle up to 1200 RPM. You want the top end to get oil up there.

Third, put in the new pilots [I would have went with #20] start with pilot fuel screws back to 1 turn, adjust as needed.

RIDE THE BIKE... put some miles on it, then worry about carb synch. Let the valves settle in to where they are happy, make sure the ignition timing is dead nuts on, then carb synch.

Don't back that center lock screw off much. The main slide adjuster is super touchy. The closer you get the synch, the less the slides will clack ;)

Where are the lobe centers?

Ah shit! ... bing bing bing - winner. :laugh:
Motorcycle Shop Owner/Operator

79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors ;)
Last edit: 02 Apr 2011 10:24 by TeK9iNe.

Please Log in or Create an account to join the conversation.

  • Old Man Rock
  • Old Man Rock's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6071
  • Thanks: 225

Re: Jetting questions

02 Apr 2011 10:48
#442134
Andy, this is a present Larry and Plum gave me back in 2008.... Follow it to the T, don't cut corners and you as well will be golden... ;)

With everything in place, Cam Degreeing, initial carb jetting, ignition timing etc... This is all going to change a tad on ya so don't go crazy trying to jet & sync quite just yet...


Sent: Tuesday, December 30, 2008 5:06 PM
Subject: Re: Start up Do's and Don'ts


After you get some miles on it an do a full service...oil & filter, valve adjustment, carb synch, check ignition timing....try to shoot for .004" on intake and .004" - .006" on exhaust. You want the exhaust a thou or two looser than the intakes.

If you want and if you can get it locally, Joe Gibbs Break In oil is excellent stuff. Make sure it's the break in oil and not one of the synthetic blends. They have many blends of Joe Gibbs.

BEFORE YOU BOLT ON THE VALVE COVER TO FIRE UP THE MOTOR....go to the auto parts store and get yourself a bottle of LL2 lifter lube. It's additive to protect the new cams. Web gives you some l-lube with them but I like to really gob it on the lobes and buckets on a fresh motor with NEW cams.

DO NOT LET THE MOTOR IDLE FOR THE FIRST 30 MINUTES OF OPERATION.

Change oil and filter in 100 miles. No more lifter lube will be needed at that point, just regular, good oil. Kendall 10 -40 has served me well over the years.

Here's what I do on a new motor and have great results.

When you assemble the head nuts and washer, use NAPA Engine Assembly Grease on the washers & the Nut Threads. Torque to spec. [use it on the cam bolts too]

Then fire up the motor and run it above 2500RPM for maybe 5 minutes with a fan blowing on the engine. You want plenty of air so you don't blue the new pipe. Then shut it off and let it cool completely down to stone cold. [even if that's overnight sitting].

Then before firing it up again, set your torque wrench to spec and go over the head nuts one more time. They will probably take some torque. Since you lubed the threads and washers and did not run the engine an extreme long time, you won't have to break each one loose again to re-torque.

Then, you're ready to hit the road and have some fun. Remember...keep the RPM above 2500 for a while yet. Go ride the bike, vary the RPM, DO NOT CRUISE AT STEADY THROTTLE OPENINGS. Don't baby it either. After it's warmed up good, run it up there to 6000 in 3rd gear. You'll feel the new power taunting you to pull the trigger!

Another thing MAKE ABSOLUTELY CERTAIN there are no fingerprints on the chrome pipe when you fire the motor....they'll burn in and stay for ever...

Basically repeat the procedure up to 500 miles do a full service...oil & filter, valve adjustment, carb synch, check ignition timing, check then again at 1500 miles... Check engine mount bolts, frame bolts, engine case bolts etc.... for they will loosen on ya.

You follow this advice and you'll love what that old girl will now and and later on do for ya...

Translation: Pull the trigger (twist her) and you better be holding on for she's going to take off on ya like a raped ape.... :evil:

OMR
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter

Phoenix, Az

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: Jetting questions

02 Apr 2011 12:17
#442152
Alright Larry first, I ran it at about 2k- 2500 rpms for @ 20-30 minutes with a fan blowing on the motor. I retorqued the head after the motor was cold. The 900 idle happened when I was messing with the fuel screws and was only for a minute. I'll hold off on the carb synch until I get some miles on it. I tried riding it with the 17.5 pilots in it and it didn't want to run right without the choke on so I figured the pilots were just way to lean. It was bad enough I was nervous to push through it to see what it did in the midrange. Lobe centers are 107.5 intake and 108.5 exhaust valves are .005-.006.
Now Dave, I lubed the shit out of the top end with torco before it went together and I changed the oil and filter after the heat cycle just to make sure I'm not pumping junk through the motor. I'm using 15-40 rotella and will probably continue to unless someone chimes in with a reason not to. I'm gonna get #20 pilots like Larry says and run it and hope for the best.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • larrycavan
  • larrycavan's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Jetting questions

02 Apr 2011 19:47 - 02 Apr 2011 19:48
#442213
Andy,

17.5's are too lean for your part of the country. #20's are about perfect, generally.

This cool weather we're still in, the bike will probably like 20's with about 1/8 -1/4 turn out on fuel screws. Summertime, close the screws up when it gets lumpy and blubbers.

You might get away with 22.5's right now but they'll be fat come the nice weather.

Get miles on it while the bores have good cross hatch in them. You only get one shot at seating the rings good and acceleration / deceleration is the best way I know of to do that..... Vary the rpm & don't over baby the motor. When you get it all dialed in, ride up and see Tom. I'm sure he'd like to twist on it a little ;)

I just got done putting 38mm GP11 Intakes with 31mm exhausts in a KZ head today.... should be a hoot :woohoo:
Last edit: 02 Apr 2011 19:48 by larrycavan.

Please Log in or Create an account to join the conversation.

  • Old Man Rock
  • Old Man Rock's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6071
  • Thanks: 225

Re: Jetting questions

03 Apr 2011 11:30 - 03 Apr 2011 11:45
#442347
Still on subject matter mind you....

Larry or others with these carbs... As with the Keihin CR's new, they come jetted way rich and understandably so.

Same with the Miks RS34's?

Andy, even in my mild build, here in AZ, 1100-1300 on the idle pending time of year/elevations... She just prefers it better there. Plus the increased oil pump pressures...

Very little installation info on the RS34's, taking good notes for a write up to pass onto the rest of us I hope... B)
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter

Phoenix, Az
Last edit: 03 Apr 2011 11:45 by Old Man Rock.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum