APE studs

  • porchev914
  • porchev914's Avatar
  • Offline
  • User
  • User
    Registered
  • Whats that? Half of my swingarm is missing?!?!?
  • Posts: 2708
  • Thanks: 19

Re: APE studs

05 Apr 2011 22:35
#442876
les holt wrote: If it's made for chasing, your fine. You don't want to cut the threads. If I have to chase threads I usually take a good bolt and grind a slot in it with a cutoff wheel in a die grinder, gives the crap a place to go.

OK Les, so bottom tap on the left is good, cutting tap on the right is bad, right?

FRANKEN Z!
1978 KZ1000 A2A with 08'Speed Triple SSSA and '06 GSXR1000 front end

Please Log in or Create an account to join the conversation.

  • T_Dub
  • T_Dub's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1441
  • Thanks: 26

Re: APE studs

05 Apr 2011 22:38
#442877
Yes Adam.
1977 KZ650B1
-810cc
-Cavanaugh Racing Head
-Mikuni RS34's
-GPR Muffler

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: APE studs

05 Apr 2011 22:58
#442882
porchev914 wrote:
les holt wrote: If it's made for chasing, your fine. You don't want to cut the threads. If I have to chase threads I usually take a good bolt and grind a slot in it with a cutoff wheel in a die grinder, gives the crap a place to go.

OK Les, so bottom tap on the left is good, cutting tap on the right is bad, right?


The one on the left is a thread chaser, the one on the right is a bottoming tap for use in blind holes. And they are both fine to use as long as you don't cross thread the bottoming tap it won't "cut" new threads. An 8x1mm tap won't take any extra material out of an 8x1mm hole after all how do you think they got the threads in there?
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: APE studs

05 Apr 2011 23:05
#442885
Close there, actually a "Bottoming tap" has no taper and will not start in just a fresh drilled hole for the size. It is for cutting to the bottom of a blind hole.
Check this; en.wikipedia.org/wiki/Tap_and_die
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • larrycavan
  • larrycavan's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: APE studs

05 Apr 2011 23:10
#442887
Whatever with the threads.... The only thing I'd tell you is loctite the studs in rather than using oil. I use red on all the studs. If you ever want to remove them, a little heat does the trick. I like them planted in nice an firm so I can pull 40lbs of torque on them. Works great for me... :)

Please Log in or Create an account to join the conversation.

  • porchev914
  • porchev914's Avatar
  • Offline
  • User
  • User
    Registered
  • Whats that? Half of my swingarm is missing?!?!?
  • Posts: 2708
  • Thanks: 19

Re: APE studs

05 Apr 2011 23:24
#442890
Motor Head wrote: Close there, actually a "Bottoming tap" has no taper and will not start in just a fresh drilled hole for the size. It is for cutting to the bottom of a blind hole.
Check this; en.wikipedia.org/wiki/Tap_and_die
Thanks for the clarification. So then, the taps I bought are specifically for cleaning/straightening threads, and not actual bottom taps for cutting to the bottom of a blind hole. Check on the red locktite Larry :)
FRANKEN Z!
1978 KZ1000 A2A with 08'Speed Triple SSSA and '06 GSXR1000 front end

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: APE studs

06 Apr 2011 01:23
#442917
andy9802gt wrote:
porchev914 wrote:
les holt wrote: If it's made for chasing, your fine. You don't want to cut the threads. If I have to chase threads I usually take a good bolt and grind a slot in it with a cutoff wheel in a die grinder, gives the crap a place to go.

OK Les, so bottom tap on the left is good, cutting tap on the right is bad, right?


The one on the left is a thread chaser, the one on the right is a bottoming tap for use in blind holes. And they are both fine to use as long as you don't cross thread the bottoming tap it won't "cut" new threads. An 8x1mm tap won't take any extra material out of an 8x1mm hole after all how do you think they got the threads in there?
one on the right looks like a plain old tap to me,botteming tap is not tapered B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • les holt
  • les holt's Avatar
  • Offline
  • Vendor
  • Vendor
    Registered
  • Posts: 1633
  • Thanks: 286

Re: APE studs

06 Apr 2011 08:17
#442939
Your fine porchev914, When using a tap, all that writing on a tap does mean something. Can't remember if metric uses some system but on a standard tap, look for something like h-2 or h-3. That number designates how much over nominal the tap is. For every 1 over is equal to .0005 oversize. You wouldn't want to use an h-10 or the like, they are for parts that are going to be coated or someother process that will decrease hole size after treating.

Please Log in or Create an account to join the conversation.

  • testarossa
  • testarossa's Avatar
  • Offline
  • User
  • User
    Registered
  • Attack life, it's only trying to kill you.
  • Posts: 3673
  • Thanks: 83

Re: APE studs

06 Apr 2011 08:53
#442944
With metric taps it D instead of H. On an M10 fastener a D3 tap corresponds to a 4H class of fit (closer tolerance) and a D4/D5 will get you a 6H class of fit (looser tolerance and potentially more slop.) 6H is actually the middle of the road tolerance found on metric fasteners in the US. So just make sure that you don't have a tap with something bigger than D5. Porchev, I would go with the thread chaser that you have pictured on the left. That's basically what Les is talking about by cutting a slot in a good bolt.
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN

Please Log in or Create an account to join the conversation.

  • APE Jay
  • APE Jay's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: APE studs

06 Apr 2011 13:48
#442984
A word of caution. As you didn't purchase these new, be sure you have Kawasaki studs. They have two different thread pitch. 1.5mm on the case end and 1.25 on the nut end.

The reason I bring this up is because Suzuki studs are the same pitch on both ends, and there are some Suzukis we make that are the same length as KZ Kawasakis.

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: APE studs

06 Apr 2011 17:41
#443033
Jordan. are u still there . lol:P
before u loctite those studs , pre fit the gaskets cyls and head,and washers.check the thread length at the top. u may find that the odd studd threads in deaper and u will be short up top. therefore u need to adjust the depth, then lock em in.
Good luck.
M
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • Zedone
  • Zedone's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 397
  • Thanks: 14

Re: APE studs

07 Apr 2011 15:32
#443247
Jay, THANKS for that info on the GS studs! I had no idea how close in appearance they are to the Z1.

Mark1122 makes an excellent point, if the studs are too high in the head you can still torque them to spec.. however the torque will not be on the head itself but rather on the stud leaving a gap under the nut causing all sorts of issues. Doug
1977 KZ1000A1
1977 KZ1000A1 (Superbike Project)
1969 Chevrolet C/10 Short Fleet

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum