APE studs
- jordan
-
Topic Author
- Offline
- User
-

Registered
- Posts: 965
- Thanks: 5
APE studs
05 Apr 2011 19:31
Finishing up my bottom end and noticed that the APE cylinder studs i purchased ,used from a member here quite some time back, dont thread in any of the holes very well. I can get them only a turn in or so before it gets tight and im worried about stripping the threads. The old studs turn in, and almost look smaller than the APE ones. I know they are thicker but im wondering if maybe my threads are different. What thread size/pitch am i supposed to have? I will run to a hardware store and see if i can turn the right thread nut onto the studs to see if i have the right ones
KZ810 streetfighter kz/gpz/gsxr
1983 gs1100e
1979 KZ 1000 1428 dragbike project
1974 kawasaki H1 500 sold
1972 Kawasaki s2 350-parted on ebay
1973 Kawasaki s2 350-parted on ebay
1982 kz750(sold)
1978 kz650 hardtail(sold)
1975 honda xl250-sold
1971 yamaha R5-sold
1982 yamaha xs400
1983 gs1100e
1979 KZ 1000 1428 dragbike project
1974 kawasaki H1 500 sold
1972 Kawasaki s2 350-parted on ebay
1973 Kawasaki s2 350-parted on ebay
1982 kz750(sold)
1978 kz650 hardtail(sold)
1975 honda xl250-sold
1971 yamaha R5-sold
1982 yamaha xs400
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: APE studs
05 Apr 2011 19:47
oil the threads
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- CoreyClough
-
- Offline
- User
-

Registered
- GPz550 Addiction
- Posts: 1093
- Thanks: 83
Re: APE studs
05 Apr 2011 20:30
Old thread lock in the threads? I'd run a thread chaser in the holes, and vacuum them out afterwards. That's what I did when I replaced the stock studs with APE Studs.
'85 GPz550(ZX550-A2)
GPz550 Base Manual --> tinyurl.com/ze5b3qo
GPz550 Supplement Manual --> tinyurl.com/h34d2o6
GPz550.com --> www.nwsca.com/scripts/gpz_forum_2005/default.asp
First Race Win GPz550 --> tinyurl.com/o5y3ftp
GPz550 Base Manual --> tinyurl.com/ze5b3qo
GPz550 Supplement Manual --> tinyurl.com/h34d2o6
GPz550.com --> www.nwsca.com/scripts/gpz_forum_2005/default.asp
First Race Win GPz550 --> tinyurl.com/o5y3ftp
Please Log in or Create an account to join the conversation.
- les holt
-
- Offline
- Vendor
-

Registered
- Posts: 1633
- Thanks: 286
Re: APE studs
05 Apr 2011 20:39 - 05 Apr 2011 20:42
Upside down maybe?:ohmy: Course threads go into case. I had 1 that didn't want to start, grabbed my glasses and what do you know, upside down.
www.facebook.com/PdmCustomFabrication
76 kz 900 turbo
77 LTD 1000 turbo
2 78 Z1R's
72 H2
kzrider.com/forum/13-bike-related/491552...one-followed-me-home
accelerate.presspublisher.us/issue/issue-6-2012/article/ltd
www.cycleworld.com/2013/09/04/2013-cycle...-concours-bike-show/
76 kz 900 turbo
77 LTD 1000 turbo
2 78 Z1R's
72 H2
kzrider.com/forum/13-bike-related/491552...one-followed-me-home
accelerate.presspublisher.us/issue/issue-6-2012/article/ltd
www.cycleworld.com/2013/09/04/2013-cycle...-concours-bike-show/
Last edit: 05 Apr 2011 20:42 by les holt.
Please Log in or Create an account to join the conversation.
- andy9802gt
-
- Offline
- User
-

Registered
- If it tastes that good, eat it yourself.
- Posts: 695
- Thanks: 19
Re: APE studs
05 Apr 2011 21:15les holt wrote: Upside down maybe?:ohmy: Course threads go into case. I had 1 that didn't want to start, grabbed my glasses and what do you know, upside down.
YAHTZEE! We have a weiner, folks.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
Please Log in or Create an account to join the conversation.
- KZ250LTD
-
- Offline
- User
-

Registered
- Posts: 1311
- Thanks: 16
Last edit: 13 Feb 2012 18:57 by KZ250LTD.
Please Log in or Create an account to join the conversation.
- Samwell
-
- Offline
- User
-

Registered
- Posts: 260
- Thanks: 1
Re: APE studs
05 Apr 2011 22:02
A thread pitch gauge will help you compare them. If memory serves they at 10m and the top and bottom have different pitches. See if your head nuts thread on.
--
Current Rides: 2013 BMW R1200GSW, 1972 BMW R75/5
Current Project: 1978 KZ1000A2: Supercrank'd by Falicon, APE studs and nuts, Dyna Green coils, powder coated frame and fenders, Stainless brake lines, dual front discs, pods, Kerker Exhaust, 1075cc with JE pistons
Current Rides: 2013 BMW R1200GSW, 1972 BMW R75/5
Current Project: 1978 KZ1000A2: Supercrank'd by Falicon, APE studs and nuts, Dyna Green coils, powder coated frame and fenders, Stainless brake lines, dual front discs, pods, Kerker Exhaust, 1075cc with JE pistons
Please Log in or Create an account to join the conversation.
- porchev914
-
- Offline
- User
-

Registered
- Whats that? Half of my swingarm is missing?!?!?
- Posts: 2708
- Thanks: 19
Re: APE studs
05 Apr 2011 22:03What about using a bottom tap thats made for chasing threads instead of cutting new ones? Do you think that would cause a problem as well? I ask because I bought a bottom tap set specifically for chasing all the threads in my cases. Now you have me wondering if thats a bad idea?KZ250LTD wrote:CoreyClough wrote: Old thread lock in the threads? I'd run a thread chaser in the holes, and vacuum them out afterwards. That's what I did when I replaced the stock studs with APE Studs.
Just a note, if you're going to chase the holes use an old stud not anything from a tap/die set. The threads are more or less M10x1.25 IIRC but the tap is bigger than the stock hole which is slightly smaller and you'll overtap the holes if you use it to chase the threads which means your studs will be loose
FRANKEN Z!
1978 KZ1000 A2A with 08'Speed Triple SSSA and '06 GSXR1000 front end
1978 KZ1000 A2A with 08'Speed Triple SSSA and '06 GSXR1000 front end
Please Log in or Create an account to join the conversation.
- les holt
-
- Offline
- Vendor
-

Registered
- Posts: 1633
- Thanks: 286
Re: APE studs
05 Apr 2011 22:13
If it's made for chasing, your fine. You don't want to cut the threads. If I have to chase threads I usually take a good bolt and grind a slot in it with a cutoff wheel in a die grinder, gives the crap a place to go.
www.facebook.com/PdmCustomFabrication
76 kz 900 turbo
77 LTD 1000 turbo
2 78 Z1R's
72 H2
kzrider.com/forum/13-bike-related/491552...one-followed-me-home
accelerate.presspublisher.us/issue/issue-6-2012/article/ltd
www.cycleworld.com/2013/09/04/2013-cycle...-concours-bike-show/
76 kz 900 turbo
77 LTD 1000 turbo
2 78 Z1R's
72 H2
kzrider.com/forum/13-bike-related/491552...one-followed-me-home
accelerate.presspublisher.us/issue/issue-6-2012/article/ltd
www.cycleworld.com/2013/09/04/2013-cycle...-concours-bike-show/
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: APE studs
05 Apr 2011 22:13porchev914 wrote: What about using a bottom tap thats made for chasing threads instead of cutting new ones? Do you think that would cause a problem as well? I ask because I bought a bottom tap set specifically for chasing all the threads in my cases. Now you have me wondering if thats a bad idea?
What, you didn't build a tap out of Carbon Fiber? :lol:
Please Log in or Create an account to join the conversation.
- porchev914
-
- Offline
- User
-

Registered
- Whats that? Half of my swingarm is missing?!?!?
- Posts: 2708
- Thanks: 19
Re: APE studs
05 Apr 2011 22:26
:laugh: The thought crossed my mind, but I don't wanna put Sears out of business
FRANKEN Z!
1978 KZ1000 A2A with 08'Speed Triple SSSA and '06 GSXR1000 front end
1978 KZ1000 A2A with 08'Speed Triple SSSA and '06 GSXR1000 front end
Please Log in or Create an account to join the conversation.
- T_Dub
-
- Offline
- User
-

Registered
- Posts: 1441
- Thanks: 26
Re: APE studs
05 Apr 2011 22:34
I didn't have to chase at all to do mine, but that was the first time it was apart, so there wasn't any crud. Couple of the top threads came out with the stud though on some of them.
1977 KZ650B1
-810cc
-Cavanaugh Racing Head
-Mikuni RS34's
-GPR Muffler
-810cc
-Cavanaugh Racing Head
-Mikuni RS34's
-GPR Muffler
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
