Head Gasket

  • Frampty
  • Frampty's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 3
  • Thanks: 0

Head Gasket

08 Apr 2011 16:29
#443439
Hi there
(SR)Z650-D2 1979 bought from ebay last year,imported to the UK from USA about the middle nineties.
Am having a few problems ,the bike is very difficult to start. Bought some new spark plugs ,condenser and points and had the timing checked,still difficult to start.
Last weekend managed to get it to start and went out for a 50mile ride,when I returned home there was oil all over my boots.looks like the head gasket is leaking.
Is it possible to change the Head Gasket while the engine is in situ?
Just would like to get a few days when I can get out and ride

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: Head Gasket

08 Apr 2011 16:57
#443443
clean motor up first and make sure its not a valve cover leaking.
have you checked valve clearances and had carbs cleaned? B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • Mcdroid
  • Mcdroid's Avatar
  • Offline
  • Sustaining Member
  • Sustaining Member
    Registered
  • Gone Kwackers
  • Posts: 6909
  • Thanks: 530

Re: Head Gasket

08 Apr 2011 17:05
#443447
wireman wrote: clean motor up first and make sure its not a valve cover leaking.
have you checked valve clearances and had carbs cleaned? B)

+1 on the wireman
Michael
Victoria, Texas

1982 GPz750
1977 KZ1000A
1978 KZ1000A
1982 GPz1100
1975 Z2A

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Head Gasket

08 Apr 2011 17:35
#443448
The spray on foot powder will quickly show where the leak is, it's water removable. Just make sure the engine is degreased well to remove any oil residue before spraying with the foot powder.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: Head Gasket

08 Apr 2011 17:59
#443457
u should do a compression test while u are at it. u could have poor compression causing a hard stat issue, or blow-by causing oil leaks.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • Kraz1
  • Kraz1's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 394
  • Thanks: 30

Re: Head Gasket

08 Apr 2011 19:21
#443462
Also check the Tach Drive #16-Gasket/#15-Seal/#13-O'Ring which is in the Valve Cover on that year.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum