77 KZ1000 Help..."barn find"

  • czombie
  • czombie's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 3
  • Thanks: 0

77 KZ1000 Help..."barn find"

08 Apr 2011 21:17
#443484
Hey guys....I've recently purchased a 77 kz1000A from a guy and I have a question.

I took the sprocket side cover off to inspect things and noticed that there wasn't a nut holding the sprocket on. I'm assuming the guy I bought it from robbed it and possibly the CORRECT sprocket for one of his other kawi's. Anyways I'm concerned at how much of the output shaft splines are sticking out past the seal face. There are only about 3/8 of an inch of splines exposed and I was just checking to make sure this is the normal allowance. It moves fine in neutral, locks up in gear, normal lash, etc. It just didn't look like enough meat to me for the sprocket to be secure and rigid enough. As a matter of fact the sprocket that was one there still had room left before it would flush up to the edge of the splines. There was still spline room left on the sprocket to slide. Maybe this is the wrong sprocket size...?? Maybe it's normal...?? I have no clue. I'm new to working on bikes, especially Kawi's....

Like I said there's about 3/8 of an inch of splines exposed....Also the guy that I bought it from parked the bike running a few years back. Too old and broken down to ride it anymore. He assured me the motor and everything was sound....But you know how that goes.

thx guys....

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: 77 KZ1000 Help..."barn find"

08 Apr 2011 21:27
#443485
Ask at www.z1enterprises.com They are very knowledgeable about these old Kawasaki's.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • JR
  • JR's Avatar
  • Offline
  • Sustaining Member
  • Sustaining Member
    Registered
  • Posts: 2981
  • Thanks: 501

Re: 77 KZ1000 Help..."barn find"

08 Apr 2011 21:36
#443490
Lots of knowledgeable people here also. Hang around. I'm sure someone with the answer will be along shortly. If you have a chance a photo might help. Welcome to the site
1980 kz750E1, Delkevic exhaust

Please Log in or Create an account to join the conversation.

  • czombie
  • czombie's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 3
  • Thanks: 0

Re: 77 KZ1000 Help..."barn find"

08 Apr 2011 21:54
#443495
I did early today actually...they looked but couldn't find any specs.

If I don't find out before Monday I'll call redline.

Please Log in or Create an account to join the conversation.

  • testarossa
  • testarossa's Avatar
  • Offline
  • User
  • User
    Registered
  • Attack life, it's only trying to kill you.
  • Posts: 3673
  • Thanks: 83

Re: 77 KZ1000 Help..."barn find"

08 Apr 2011 22:06 - 08 Apr 2011 22:07
#443496
3/8" of splines sounds about right to me. It would have had a 630 chain as stock. 630 corresponds to a 3/8" wide sprocket. As for the lack of a nut, I guess it could run for a while like that, but I bet it wouldn't end well. It wouldn't be the first time that a neglected bike had lost the nut on the countershaft sprocket. Probably best to replace the chain and sprockets together to eliminate any doubt.

EDIT: BTW welcome to KZR! Post some pics when you find the time.
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN
Last edit: 08 Apr 2011 22:07 by testarossa.

Please Log in or Create an account to join the conversation.

  • czombie
  • czombie's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 3
  • Thanks: 0

Re: 77 KZ1000 Help..."barn find"

09 Apr 2011 00:01 - 09 Apr 2011 00:01
#443534
testarossa wrote: 3/8" of splines sounds about right to me. It would have had a 630 chain as stock. 630 corresponds to a 3/8" wide sprocket. As for the lack of a nut, I guess it could run for a while like that, but I bet it wouldn't end well. It wouldn't be the first time that a neglected bike had lost the nut on the countershaft sprocket. Probably best to replace the chain and sprockets together to eliminate any doubt.

EDIT: BTW welcome to KZR! Post some pics when you find the time.

thx for the reply man....I feel much better at ease now.

Now I can get started getting this beast runnin.

:evil:
Last edit: 09 Apr 2011 00:01 by czombie.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum