1979 KZ1000 E-1
- Hambo
-
Topic Author
- Offline
- User
-

Registered
- Posts: 19
- Thanks: 0
1979 KZ1000 E-1
09 Apr 2011 12:27
Hello,
I have a 1979 KZ1000 E-1 Shaft. My problem started when the cam guide (the L shaped one) came loose and shredded inside the motor. The cam chain was flopping around but fortunately I only had a half a mile to home. I broke the motor down, replaced the guide, gears and chain,reassembled the motor, checked valve clearances and , cleaned carbs and now it will not start. The cams and crank are lined up correctly, I have spark and gas, but to no avail it will not start. Can anyone help??
I have a 1979 KZ1000 E-1 Shaft. My problem started when the cam guide (the L shaped one) came loose and shredded inside the motor. The cam chain was flopping around but fortunately I only had a half a mile to home. I broke the motor down, replaced the guide, gears and chain,reassembled the motor, checked valve clearances and , cleaned carbs and now it will not start. The cams and crank are lined up correctly, I have spark and gas, but to no avail it will not start. Can anyone help??
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 1979 KZ1000 E-1
09 Apr 2011 13:24
If not already done, would assure that the black and green wires from the igniter to the ignition coils haven't been reversed.
Am thinking the black wire is supposed to go to whichever coil is firng the outside spark plugs.
Good Fortune!
Am thinking the black wire is supposed to go to whichever coil is firng the outside spark plugs.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Hambo
-
Topic Author
- Offline
- User
-

Registered
- Posts: 19
- Thanks: 0
Re: 1979 KZ1000 E-1
09 Apr 2011 13:37
Thank you Patton for the reply. I didnt change any wiring before or after I took apart and reassembled the motor. I didnt change anything. Thats why I am so baffled.
Please Log in or Create an account to join the conversation.
- Hambo
-
Topic Author
- Offline
- User
-

Registered
- Posts: 19
- Thanks: 0
Re: 1979 KZ1000 E-1
09 Apr 2011 13:40
Also,
I dont have an igntor or TCI but I believe the electronic points and coils are aftermarket.
I dont have an igntor or TCI but I believe the electronic points and coils are aftermarket.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 1979 KZ1000 E-1
09 Apr 2011 13:49Hambo wrote: Also,
I dont have an igntor or TCI but I believe the electronic points and coils are aftermarket.
Perhaps the stock ignition has been replaced with a Dyna-S ignition.
Could double check ignition timing.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- gengomerpyle
-
- Offline
- User
-

Registered
- Posts: 616
- Thanks: 17
Re: 1979 KZ1000 E-1
09 Apr 2011 14:22i would like to someday get that for my bike when i ever put the dyna coils on that i have sitting here.
1982 GPZ750R1 ELR
1978 Honda CB750F SuperSport
1971 Honda CB750K
1970 Honda CL100 Scrambler
1978 Honda CB750F SuperSport
1971 Honda CB750K
1970 Honda CL100 Scrambler
Please Log in or Create an account to join the conversation.
- RonKZ650
-
- Offline
- User
-

Registered
- Posts: 3719
- Thanks: 252
Re: 1979 KZ1000 E-1
09 Apr 2011 23:13
Check compression. Most KZ1000 engine reassembly if not done carefully results in cams being referenced to the wrong marks.
321,000 miles on KZ's that I can remember. Not going to see any more.
Please Log in or Create an account to join the conversation.
- Hambo
-
Topic Author
- Offline
- User
-

Registered
- Posts: 19
- Thanks: 0
Re: 1979 KZ1000 E-1
10 Apr 2011 14:05 - 10 Apr 2011 14:11
Is it possible that my crank is 180 out of allignment? The crank turns 2 times to the cams one correct? So maybe Im one turn off? And also, what is the other T-mark that is 180 degrees across from the other T-mark for?
Last edit: 10 Apr 2011 14:11 by Hambo. Reason: added to question
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 1979 KZ1000 E-1
10 Apr 2011 14:43Hambo wrote: Is it possible that my crank is 180 out of allignment? The crank turns 2 times to the cams one correct? So maybe Im one turn off? And also, what is the other T-mark that is 180 degrees across from the other T-mark for?
T mark for cylinders 1 and 4, when aligned with the permanent case mark, shows when pistons in the outside cylinders are at top dead center.
T mark for cylinders 2 and 3 (on the other end of the advancer), when aligned with the permanent case mark, shows when pistons in the inside cylinders are at top dead center.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Hambo
-
Topic Author
- Offline
- User
-

Registered
- Posts: 19
- Thanks: 0
Re: 1979 KZ1000 E-1
11 Apr 2011 09:29
Well,
Ive checked my crank/cam line up marks-dead on, checked static timimg with light and both coils fire on the appropiate marks. I guess Ill clean the carbs again. Thanks for everybody's help. I am getting too frustrated but I will continue to try to figure this $*(^&##$ problem out. It will not win!!!
Thanks Hambo
Ive checked my crank/cam line up marks-dead on, checked static timimg with light and both coils fire on the appropiate marks. I guess Ill clean the carbs again. Thanks for everybody's help. I am getting too frustrated but I will continue to try to figure this $*(^&##$ problem out. It will not win!!!
Thanks Hambo
Please Log in or Create an account to join the conversation.
- KZ_Rage
-
- Offline
- User
-

Registered
- Kentucky Bourbon Barrel Ale
- Posts: 891
- Thanks: 19
Re: 1979 KZ1000 E-1
11 Apr 2011 10:08
If you are 100% sure you have the timing right, there's gas getting into the chambers and the ignition is sending spark then I'd be a little frustrated too!
The plug wires are on the correct cylinders right? The spark is white/blue?
Are you getting any attempt to fire a all, like a pop once and awhile? What's the plug look/smell like after an attempted start when you pull it?
I'm assuming you still have the original pumper carbs?
The plug wires are on the correct cylinders right? The spark is white/blue?
Are you getting any attempt to fire a all, like a pop once and awhile? What's the plug look/smell like after an attempted start when you pull it?
I'm assuming you still have the original pumper carbs?
1979 KZ1000E1 SOLD!
1984 KZ550F2 SOLD!
2006 ZG1000A6F (Totaled)
2001 ZRX1200R (Sold)
2001 Sprint 955i ST (daily rider)
1984 KZ550F2 SOLD!
2006 ZG1000A6F (Totaled)
2001 ZRX1200R (Sold)
2001 Sprint 955i ST (daily rider)
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: 1979 KZ1000 E-1
11 Apr 2011 10:17 - 11 Apr 2011 15:31Could try spraying starting fluid into the carb intakes while trying to start the engine.
This may help determine whether it's carb related.
As kz_rage asked, what's plug tip condition immediately after a failed effort to start the engine?
Combustion chamber may be flooded.
Could de-flood :woohoo: using a long stemmed lit match inserted into the spark plug hole.
Or spray starting fluid into the spark plug hole, and blow it clear with compressed air.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 11 Apr 2011 15:31 by Patton.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
