removing baffle?

  • boonies07
  • boonies07's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • boonie on kz 1000
  • Posts: 9
  • Thanks: 0

removing baffle?

11 Apr 2011 13:03
#444068
i was wondering if it would be bad for bike to remove baffle from kerker exhaust. the carbs were jetted for exhaust.

Please Log in or Create an account to join the conversation.

  • Mcdroid
  • Mcdroid's Avatar
  • Offline
  • Sustaining Member
  • Sustaining Member
    Registered
  • Gone Kwackers
  • Posts: 6909
  • Thanks: 530

Re: removing baffle?

11 Apr 2011 13:46
#444072
It is likely the bike, if running well with the baffle, is jetted for the pipe + baffle, ergo, removal of the baffle and the bike will not be jetted correctly. It won't hurt the bike to run it that way but performance may not be optimal.
Michael
Victoria, Texas

1982 GPz750
1977 KZ1000A
1978 KZ1000A
1982 GPz1100
1975 Z2A

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: removing baffle?

11 Apr 2011 18:33
#444127
It will make it run lean which is never good.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: removing baffle?

11 Apr 2011 19:06
#444132
even if u rejet to correct the fuel ratio , u will feel less bottom end.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • trianglelaguna
  • trianglelaguna's Avatar
  • Offline
  • User
  • User
    Registered
  • New and improved - extra strength
  • Posts: 8019
  • Thanks: 236

Re: removing baffle?

11 Apr 2011 23:13
#444178
i had smooth bores and used to pull the whole can off of Z-1 once in a while when i was a young punk...the neighbors will stop you before the jetting will...or the cops...:)
1976 KZ900
2003 ZX12R
2007 FZ1000
2004 ninja 250R for wife

Please Log in or Create an account to join the conversation.

  • dejavoodo41
  • dejavoodo41's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 405
  • Thanks: 14

Re: removing baffle?

12 Apr 2011 00:30
#444211
my bike has only had the baffle out twice. Once on the dyno and once when what the previous owner called a baffle came out on my way to work. It was pretty much unbearable to ride at highway speeds and had a migrane after 30 minutes with ear plugs in. The difference between my V&H pro pipe open and with the comp baffle on the dyno was about a quarter of a hp and was noticeably stronger in the midrange so I'll take more usable power and less noise.
1977 KZ1000A With 1980 KZ1000A MKII engine, Wiseco 1105 kit, Dyna S Ignition, 3 Ohm Dyna Coils, Cams, Mikuni RS34 Carbs, Vance and Hines Pro Pipe with Comp Baffle

New Smyrna Beach, FL

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum