Altenator removal
- Zedone
-
Topic Author
- Offline
- User
-

Registered
- Posts: 397
- Thanks: 14
Altenator removal
16 Apr 2011 04:56
1977 KZ1000A1
I'm pulling my alt to reinstall the starter clutch that the previous owner took out. Just for anyones knowledge the "Haynes Manual" (god I hate this thing) is WRONG and you do NOT use the rear axle to thread into the alt. it is the swingarm pivot bolt that threads into the alt.
Anyway, I have a spare 1977KZ1000A1 crank that I'm trying to get the alt. off of so I can use that starter clutch. Can't get the alt. off. I threaded the swingarm pivot bolt all the way in and tapped with a hammer on a large washer I temp installed on it (at the nut end). Tried the same method on my bike alt and it won't budge. This method is a Curly, Larry, & Moe approach IMO.
I'm thinking I need to buy a puller tommorow (mine have gone missing) but I'm goona need to come up with a smaller sleeve to go inside the alt. threads to .go on the crank end and make sure I don't damage the end of the crank (threads). Any ideas? I might have to cut a steel plug
Also, I pulled the alt cover off of my 2nd 1977 KZ1000A1 so I could steal the starter clutch idler gear from it and I noticed it has a 10mm alt crank bolt in it. My other 1977 KZ1000A1 has a 8mm alt crank bolt. This motor's cases have never been apart but yet the serial # confirms its a A1. I know the 1978 KZ1000A2 has a 10mm alt crank bolt but wtf is going on? Are the A1 & A2 cranks identical except for this upgrade? I remember reading there were issues with some alts coming off with the 1000 (hence the bolt upgrade) not sure on the Z1 though.
And does anyone know (for a fact) that the starter clutch idler gears are IDENTICAL between the 1977 KZ1000A1 & 1978 KZ1000A2? I'm going to check Kawasaki's part #'s on their site.
Thanks, Doug
I'm pulling my alt to reinstall the starter clutch that the previous owner took out. Just for anyones knowledge the "Haynes Manual" (god I hate this thing) is WRONG and you do NOT use the rear axle to thread into the alt. it is the swingarm pivot bolt that threads into the alt.
Anyway, I have a spare 1977KZ1000A1 crank that I'm trying to get the alt. off of so I can use that starter clutch. Can't get the alt. off. I threaded the swingarm pivot bolt all the way in and tapped with a hammer on a large washer I temp installed on it (at the nut end). Tried the same method on my bike alt and it won't budge. This method is a Curly, Larry, & Moe approach IMO.
I'm thinking I need to buy a puller tommorow (mine have gone missing) but I'm goona need to come up with a smaller sleeve to go inside the alt. threads to .go on the crank end and make sure I don't damage the end of the crank (threads). Any ideas? I might have to cut a steel plug
Also, I pulled the alt cover off of my 2nd 1977 KZ1000A1 so I could steal the starter clutch idler gear from it and I noticed it has a 10mm alt crank bolt in it. My other 1977 KZ1000A1 has a 8mm alt crank bolt. This motor's cases have never been apart but yet the serial # confirms its a A1. I know the 1978 KZ1000A2 has a 10mm alt crank bolt but wtf is going on? Are the A1 & A2 cranks identical except for this upgrade? I remember reading there were issues with some alts coming off with the 1000 (hence the bolt upgrade) not sure on the Z1 though.
And does anyone know (for a fact) that the starter clutch idler gears are IDENTICAL between the 1977 KZ1000A1 & 1978 KZ1000A2? I'm going to check Kawasaki's part #'s on their site.
Thanks, Doug
1977 KZ1000A1
1977 KZ1000A1 (Superbike Project)
1969 Chevrolet C/10 Short Fleet
1977 KZ1000A1 (Superbike Project)
1969 Chevrolet C/10 Short Fleet
Please Log in or Create an account to join the conversation.
- andy9802gt
-
- Offline
- User
-

Registered
- If it tastes that good, eat it yourself.
- Posts: 695
- Thanks: 19
Re: Altenator removal
16 Apr 2011 07:43
drop a ball bearing down the hole in the alternator and then use the puller. A 6mm nut on edge will work too.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Altenator removal
16 Apr 2011 09:01
X2
i cant see why a puller would give u any more leverage than the bolt.
if it make u feel any better. the crank is hardend so "theroreticaly" the bolt will strip before the crank. U may need to hit that bolt hard.
Not sure about the dif parts . I know ma kwa did some weird sh!t. the z1’s had a 6mm bolt.
u will just have to see what u have when u get them all apart.
i cant see why a puller would give u any more leverage than the bolt.
if it make u feel any better. the crank is hardend so "theroreticaly" the bolt will strip before the crank. U may need to hit that bolt hard.
Not sure about the dif parts . I know ma kwa did some weird sh!t. the z1’s had a 6mm bolt.
u will just have to see what u have when u get them all apart.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Please Log in or Create an account to join the conversation.
- martin_csr
-
- Offline
- User
-

Registered
- Posts: 7993
- Thanks: 1648
Last edit: 13 Feb 2013 11:32 by martin_csr.
Please Log in or Create an account to join the conversation.
- Zedone
-
Topic Author
- Offline
- User
-

Registered
- Posts: 397
- Thanks: 14
Re: Altenator removal
16 Apr 2011 10:19
:laugh: thanks for the link Patton (I think,:lol: ). I am going to get those suckers off later today! It's been ages since I worked on that side of the crank.
I did a search on Kaw's website and for those concerned, the idler gear pt# 21167-002 & the pin it runs on pt# 13002-007 is the same from the 73 Z1 all the way up to the 1978 KZ1000A2A. So they shd be totally interchangeable.
Thanks for all the help guys, later
I did a search on Kaw's website and for those concerned, the idler gear pt# 21167-002 & the pin it runs on pt# 13002-007 is the same from the 73 Z1 all the way up to the 1978 KZ1000A2A. So they shd be totally interchangeable.
Thanks for all the help guys, later
1977 KZ1000A1
1977 KZ1000A1 (Superbike Project)
1969 Chevrolet C/10 Short Fleet
1977 KZ1000A1 (Superbike Project)
1969 Chevrolet C/10 Short Fleet
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Altenator removal
16 Apr 2011 10:46
do u have 1 of those manual impact drivers? like mentioned in that thread. that is a great idea. if that failed then i would try the impact gun.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- Zedone
-
Topic Author
- Offline
- User
-

Registered
- Posts: 397
- Thanks: 14
Re: Altenator removal
16 Apr 2011 21:15
Update:
I blasted some WD40 @ the inside of the rotor and let it sit overnight (it may of helped a bit). Then I installed the swingarm pivot bolt all the way and gave it a sharp tap straight on the head with a hammer. I have a USA made oil filter wrench that works excellent around the alt. to prevent it from turning. Tightened the bolt @ 1/2 turn, sharp tap straight on with the hammer again, and it came right off. Did the same procedure to my spare crank and.... came right off.
The PO didn't re-install the keyway on mt bike crank (what a brain cell) so I have a spare from my spare crank.....
All is good now, Cheers, Doug
I blasted some WD40 @ the inside of the rotor and let it sit overnight (it may of helped a bit). Then I installed the swingarm pivot bolt all the way and gave it a sharp tap straight on the head with a hammer. I have a USA made oil filter wrench that works excellent around the alt. to prevent it from turning. Tightened the bolt @ 1/2 turn, sharp tap straight on with the hammer again, and it came right off. Did the same procedure to my spare crank and.... came right off.
The PO didn't re-install the keyway on mt bike crank (what a brain cell) so I have a spare from my spare crank.....
All is good now, Cheers, Doug
1977 KZ1000A1
1977 KZ1000A1 (Superbike Project)
1969 Chevrolet C/10 Short Fleet
1977 KZ1000A1 (Superbike Project)
1969 Chevrolet C/10 Short Fleet
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
