Replacing valve guides

  • freshwombat
  • freshwombat's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 2
  • Thanks: 0

Replacing valve guides

22 Apr 2011 00:57
#446228
I'm planning on replacing the valve guides in my z500 and can get a heat gun from work to do it.

Just wondering if anyone has any tips?

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: Replacing valve guides

22 Apr 2011 01:19
#446232
im not sure if theyre the same as the 900/1000 but id suggest doing a really good job of cleaning out all the carbon out around the guide before removing ,might want to use the oven to heat it up when wifes not looking :laugh:
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • carpenoctem
  • carpenoctem's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 10
  • Thanks: 0

Re: Replacing valve guides

22 Apr 2011 01:25
#446235
A used electric oven, for free off craigslist works great. So can a dishwasher if you can tie it into your water heater to get good hot water. use extra dish detergent (like 3 times normal) and run it for 3-4 runs adding fresh soap each run.

Don't forget to string the waste hose somewhere inconspicuous. ....or out to the curb at night.

used electric ovens are also good for powder coating small parts. Toss the rack to it's highest opint and hang parts from it. make sure it never touches anything inside though.

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Replacing valve guides

22 Apr 2011 10:06
#446274
Without the correct tools, it would be best left to someone who does like a good machine shop.
The new guides after install need to be reamed to the proper inside diameter, then the valve seats re-cut to assure the correct alignment & sealing, then the installed height must be set for the shim range. Valve guides come in different outside diameters too, for the interference fit to the bore in the head. If to loose, movement/ migration can occur. If to tight the head can be cracked.
They sell a drill bit that is stepped/ piloted for drilling out the guides, it leaves a step to drive them out, but collapses the guide to remove them easily. Then there are drivers to reinstall the guide, bits for air-hammers or a normal hammer, as it is a press fit.
They also sell a Knurling kit. These reform the inner bore of the used guide, and have the reamer to re-size it again. Used to be pretty popular, but changing the guides is best for longevity.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum