Cylinder leaks
- Emberblade
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
Cylinder leaks
23 Apr 2011 19:37
What's the most likely cause of leakage between the piston and cylinder wall? please say bad rings. If I installed the rings incorrectly, would it leak badly? I can admit that I might not have done it properly. It was a wiseco piston kit that I had to get when I found out how badly pitted my cylinder was. I'm definitely gonna do it, because it leaks, I just want to be sure before I tear it down.
This website is such a great resource for a novice.
This website is such a great resource for a novice.
1982 KZ1000J ELR Clone
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: Cylinder leaks
23 Apr 2011 21:32 - 23 Apr 2011 21:35
Poor compression can be caused by a few things.
Bad piston. Bad rings. Bad valves. Bad head gasket.
Thats pretty much it.
Yes, the rings being installed incorrectly can lead to some fairly significant leakage, but the piston/cylinder clearance and fit is the most important part of the whole machine. Too much clearance is just not acceptable and leads to poor performance, plug fouling, etc.
Measure, measure, measure... you wont know if its the piston or rings unless you measure up the cylinder and piston and compare. You need some telescoping bore guages, or an inside bore micrometer.
I like to measure the cylinder at the top, middle, and bottom, both axis (length, width), then I use a small steel straight edge and .001" feeler guage to check all over for minute differences in the walls. I usually scrap/bore a sleeve if its got more than one spot out .002"
Then measure up the piston top of skirt lip to the other and the other axis, also with a straight edge again checking for visual conformity.
Subtract the piston measurement from the cylinder and you have your clearance.
Good luck.
Bad piston. Bad rings. Bad valves. Bad head gasket.
Thats pretty much it.
Yes, the rings being installed incorrectly can lead to some fairly significant leakage, but the piston/cylinder clearance and fit is the most important part of the whole machine. Too much clearance is just not acceptable and leads to poor performance, plug fouling, etc.
Measure, measure, measure... you wont know if its the piston or rings unless you measure up the cylinder and piston and compare. You need some telescoping bore guages, or an inside bore micrometer.
I like to measure the cylinder at the top, middle, and bottom, both axis (length, width), then I use a small steel straight edge and .001" feeler guage to check all over for minute differences in the walls. I usually scrap/bore a sleeve if its got more than one spot out .002"
Then measure up the piston top of skirt lip to the other and the other axis, also with a straight edge again checking for visual conformity.
Subtract the piston measurement from the cylinder and you have your clearance.
Good luck.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Last edit: 23 Apr 2011 21:35 by TeK9iNe.
The following user(s) said Thank You: Emberblade
Please Log in or Create an account to join the conversation.
- Emberblade
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
Re: Cylinder leaks
23 Apr 2011 22:46
So I just pulled the head, and the gasket was definitely leaking, and I think using RTV silicone was a mistake, it just bubbled up and leaked into the cavity that holds the camchain, causing the hiss I heard while rotating my crankshaft with the oil pan off.
But I completely lost compression on my other pistons. Now I think the valves must need to be reseated after my completely failed attempt to clean them up... crap.
Thanks!
But I completely lost compression on my other pistons. Now I think the valves must need to be reseated after my completely failed attempt to clean them up... crap.
Thanks!
1982 KZ1000J ELR Clone
Please Log in or Create an account to join the conversation.
- Tyler
-
- Offline
- User
-

Registered
- Posts: 845
- Thanks: 92
Re: Cylinder leaks
24 Apr 2011 01:52Emberblade wrote: So I just pulled the head, and the gasket was definitely leaking, and I think using RTV silicone was a mistake, it just bubbled up and leaked into the cavity that holds the camchain, causing the hiss I heard while rotating my crankshaft with the oil pan off.
But I completely lost compression on my other pistons. Now I think the valves must need to be reseated after my completely failed attempt to clean them up... crap.
Thanks!
Okay,
First, head gaskets almost never use sealant. And never reuse a head gasket.
Second, use the correct sequence to torque the head, and use the correct torque value.
Third, what did you do to the valves? Did you check clearances?
Most importantly, do you have a manual? You should if your tearing into the engine.
If I knew what I was doing all the time life wouldn't be any fun.
'80 KZ650 E 700cc, dyna ignition and coils, frame up restoration, daily driver
'81 KZ1300 A3 full restoration, custom big bore pistons, 1400cc 6 cylinder super bike
"77 KZ650 B1 - Barn Find, work in progeress
"74 Yamaha DT 400 Enduro
'80 KZ650 E 700cc, dyna ignition and coils, frame up restoration, daily driver
'81 KZ1300 A3 full restoration, custom big bore pistons, 1400cc 6 cylinder super bike
"77 KZ650 B1 - Barn Find, work in progeress
"74 Yamaha DT 400 Enduro
The following user(s) said Thank You: Emberblade
Please Log in or Create an account to join the conversation.
- Emberblade
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
Re: Cylinder leaks
24 Apr 2011 12:35 - 24 Apr 2011 13:22
A leak down test could aid diagnosis.
Good Fortune!
[Note from Patton]
Sorry, Emberblade.
I screwed up by hitting the wrong button and inadvertently edited your post. :blush:
Perhaps you could re-post the message.
As to oil having been added to cylinders through the spark plug holes and finding it has drained down past the pistons overnight, am thinking most any motor would do that.
Good Fortune!
Good Fortune!
[Note from Patton]
Sorry, Emberblade.
I screwed up by hitting the wrong button and inadvertently edited your post. :blush:
Perhaps you could re-post the message.
As to oil having been added to cylinders through the spark plug holes and finding it has drained down past the pistons overnight, am thinking most any motor would do that.
Good Fortune!
1982 KZ1000J ELR Clone
Last edit: 24 Apr 2011 13:22 by Patton.
Please Log in or Create an account to join the conversation.
- Emberblade
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
Re: Cylinder leaks
24 Apr 2011 14:06
Okay, I pulled my head off a while ago to see what was going on in there. #2 and 4 were visibly out of their seats from the carbon and rust buildup. I cleaned the valves off myself with a dremel and wire brush. That was probably a mistake and could be the cause of my problems, but I was very careful to only go down to the metal without taking any off.
I'm going to measure the valves to make sure they still fit, and if they're too far off, I'm going to have it reseated. I'll get a new head gasket, and WON'T use silicone to seal it.
Thanks!
I'm going to measure the valves to make sure they still fit, and if they're too far off, I'm going to have it reseated. I'll get a new head gasket, and WON'T use silicone to seal it.
Thanks!
1982 KZ1000J ELR Clone
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Cylinder leaks
24 Apr 2011 15:28
You said the cylinder walls are badly pitted. That would make it leak. Or, if the cylinder is worn out of round.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- Emberblade
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
Re: Cylinder leaks
24 Apr 2011 18:11
The cylinders were just bored out and I installed a wiseco piston kit. All the machining was done by an engine shop that does racecars, and the guy did a great job. I checked it with a micrometer just in case. It wasn't even a little out of whack.
What would be a good test to do on the valves if I have the top end apart? I want to see if they leak and can't put the engine back together without a new head gasket which I am waiting for. Even if I got the new gasket, I want to know my heads are good or bad. If they're fine, I want to know before I give them to the shop and get hit with an inspection fee.
Thanks!
What would be a good test to do on the valves if I have the top end apart? I want to see if they leak and can't put the engine back together without a new head gasket which I am waiting for. Even if I got the new gasket, I want to know my heads are good or bad. If they're fine, I want to know before I give them to the shop and get hit with an inspection fee.
Thanks!
1982 KZ1000J ELR Clone
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Cylinder leaks
24 Apr 2011 19:00
pore a bit varsol or some thin agent (kerosine) into the ports and see if it leaks past the valves. Don’t get any into the guides.
If it doesn’t leak the seats are good.
If it doesn’t leak the seats are good.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- Emberblade
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
Re: Cylinder leaks
24 Apr 2011 19:07
How long should I let it sit? And you mean from the places where the carbs and the exhaust pipes go?
Thanks!
Thanks!
1982 KZ1000J ELR Clone
Please Log in or Create an account to join the conversation.
- Emberblade
-
Topic Author
- Offline
- User
-

Registered
- Posts: 52
- Thanks: 0
Re: Cylinder leaks
24 Apr 2011 19:08
How about PBlaster into the ports?
1982 KZ1000J ELR Clone
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Cylinder leaks
24 Apr 2011 19:42Emberblade wrote: How long should I let it sit? And you mean from the places where the carbs and the exhaust pipes go?
Thanks!
yes thats fine.if they are going to leak u will know pretty quick.
How about PBlaster into the ports?
yes thats good. just spray some in and tip the head so the valve stem is perpendicular to your bench. after a min. , pour it out into a cup , then pour it into the next 1. or do 4 at a time if u like.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
The following user(s) said Thank You: Emberblade
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
