engine lurching on kz900

  • Onthewater2181
  • Onthewater2181's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

engine lurching on kz900

30 Apr 2011 23:09
#447904
Hello everyone.

I have pretty much completed my restoration on my 1976 KZ900. The final thing I have left is to get it running smooth.
The bike runs fine at idle and at low rpms, when I am at five and a half on the tach. The bike begins to sputter and back fire, with a loss of power for a second and then begins to lurch. Here is a list of what I have done to the bike.

New spark plugs
New pod air filters
New exhaust.
New spark plug wires.
Clean carbs
Rejet carbs one size up for exhaust and pods.
Synchronize carburetors
adjust air mixture one and a half turns out from stop
Timed with timing light.
If any one has a possible idea it would be appreciated. I am not sure where to go from here.
Thanks.

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: engine lurching on kz900

30 Apr 2011 23:38
#447910
Might be fuel starvation.

Would test ride with fuel cap ajar to rule out possible vent issue.
Assure tank interior is clean, and that petcock pick-ups inside tank aren't clogged.
And that petcock isn't clogged. And that in-line fuel filter isn't clogged.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • Nelson
  • Nelson's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 665
  • Thanks: 16

Re: engine lurching on kz900

01 May 2011 00:00
#447919
yeah, seems like you've done everythign else. when I bought mine it had horrific amounts of crap in the tank. Ran fine and then would cut out and sputter like that.

I used hi-pressure water blast inside tank to clean it. then dried interior as quick as i could with air. then installed automotive inline filters. made all the difference. gotta replace the filter once in a while.
Restoring and customizing a KZ1000. Click here to read about it.
Plated KTM, DR650, KZ1000, Former MC mechanic (eons ago). 40 yrs. of dirt and street.

Please Log in or Create an account to join the conversation.

  • Onthewater2181
  • Onthewater2181's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

Re: engine lurching on kz900

01 May 2011 00:01
#447920
Thanks for the ideas. I have checked the petcock and fuel lines. I did replace the rubber gasket on the fuel cap, did not think of the vent issue. I will try that out and see if that improve it any. Will keep you informed.

Thanks

Please Log in or Create an account to join the conversation.

  • Onthewater2181
  • Onthewater2181's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

Re: engine lurching on kz900

01 May 2011 00:07
#447923
Thanks Nelson.
When I go across the carburetors again to make absolute sure I will check the tank and clean it out. Change out the fuel filters. I did notice a hairline crack in my reserve fuel pipe on the petcock. Will check into that.

Thanks for the ideas I was running out of ideas. Sometimes you end up over thinking everything before your so confused you don't know where to go next. Better just to ask for help and save some hair on your head before you pull it all out.

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: engine lurching on kz900

01 May 2011 00:21
#447929
What brand of sparkplugs? I've had brand new NGK's fail right out of the box. I changed to Denso sparkplugs with no problems. I' using Denso W24-ESU's gapped to 0.032".

New sparkplug caps? They get old and age from heat and vibration.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • gane
  • gane's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 706
  • Thanks: 1

Re: engine lurching on kz900

01 May 2011 00:58
#447939
5 grand is mid-range. "prime candidates" are "emulsion tubes & advance unit..g
[img][/img] 1977 KZ1000A1

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: engine lurching on kz900

01 May 2011 07:49
#447971
Lurching/ surging at a constant throttle is also a sign of being to rich. Did you jet the carbs from "known" stock or just from what the P.O. had in it to begin with? There is no one answer fix-all when it comes to tuning. The one size richer for this or that is a ballpark to play in, it is usually not the final setting on jet sizes/ needle position. If you are sure your problem is fuel related and not a spark issue then do what the others have said and make sure you have good clean fuel flow then work on the carbs.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • Kidkawie
  • Kidkawie's Avatar
  • Offline
  • User
  • User
    Registered
  • I bleed premix
  • Posts: 1924
  • Thanks: 246

Re: engine lurching on kz900

01 May 2011 11:08
#447996
Carb sync, but did you set the float height?
1975 Z1 900
1994 KX250 Supermoto
2004 KX125

Please Log in or Create an account to join the conversation.

  • Old Man Rock
  • Old Man Rock's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6071
  • Thanks: 225

Re: engine lurching on kz900

01 May 2011 12:11
#448012
Due to RPM range when occurring and assuming all other replies have been accomplished/confirmed (valve clearances, ignition, carb sync etc...) first thought is manifold vacuum leak/needle clip position/jetting... Mid range jetting!

Go for a ride...
1) Hold at 65mph (~4500rpm).... does she surge back and forth as if she was missing fuel feed?

2) Hold at 65mph... Let go of the throttle and let her snap back... Popping sound/Backfire?

Then needle jet/clip too lean. Translation, more air then gas being fed into the carbs.

Just a thought...

OMR
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter

Phoenix, Az

Please Log in or Create an account to join the conversation.

  • Onthewater2181
  • Onthewater2181's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 18
  • Thanks: 0

Re: engine lurching on kz900

01 May 2011 18:09
#448082
Ok heres the scoop.

I went through and checked the timing and fuel. Fuel is flowing freely and is clean. Installed new fuel filters for safe measure. Checked my exhaust to see if maybe If that is where I was getting the popping from. tight and clean. Try the first couple of suggestions and still doing it at five and half grand on the rpm(popping). You still feel the engine pulse like it wants to go but even when bearing down on the throttle the bike is sluggish to acceleration.

Would this be a carburetor issue, and any ideas on where to go. I have 120's in it now. was thinking of dropping them down to 117.5. and a good cleaning.

Thanks again for the all the input.

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: engine lurching on kz900

01 May 2011 19:00
#448089
Would also assure jet needle clips are in the stock middle position.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum