bead blasting

  • kzrebuilder2010
  • kzrebuilder2010's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 6
  • Thanks: 0

bead blasting

03 May 2011 13:05
#448550
I recently acquired a 1980 kz750e1 for 150 bucks the motor and most of the bike is already tore down ( it's going to be fun finding where every nut and bold goes not labeled) I want to see about getting all the old black paint of the motor cand transmission housing do you guys think it will be ok to bead blast it all and then wash it thoroughly with parts washer before reassembly other wise I don't know how to get every inch between the fins of the cylinder fins thanks

kzrebuilder2010

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: bead blasting

03 May 2011 13:23
#448554
id take it to the car wash and give it a bath with some good paint stripper first to get the majority off then hit it with the glass beads,keep the beads away from any machined areas B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
The following user(s) said Thank You: kzrebuilder2010

Please Log in or Create an account to join the conversation.

  • kzrebuilder2010
  • kzrebuilder2010's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 6
  • Thanks: 0

Re: bead blasting

03 May 2011 13:32
#448555
thanks I was thinkin the same thing I have build plenty of car motors this will be my first bike motor and I won't get near the machined area just do the main surface stuff. want to either paoint it black or the same color as the rest of my bike which ever color it is I decided to go with think cafe racer but need to think long and hard about the cost and eneergy need to get it running first

Please Log in or Create an account to join the conversation.

  • Kidkawie
  • Kidkawie's Avatar
  • Offline
  • User
  • User
    Registered
  • I bleed premix
  • Posts: 1924
  • Thanks: 246

Re: bead blasting

03 May 2011 13:33
#448556
If you study the Kawasaki parts microfiche it will tell you what size bolt is used.
1975 Z1 900
1994 KX250 Supermoto
2004 KX125
The following user(s) said Thank You: kzrebuilder2010

Please Log in or Create an account to join the conversation.

  • kawsakiman
  • kawsakiman's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1246
  • Thanks: 6

Re: bead blasting

05 May 2011 18:46
#449083
run a tap through every hole before you assemble.
just blowing them out or spraying brake clean in there will not do it.
you will be suprised how much will be in there.
someday i will be able to afford my kz habit.

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: bead blasting

05 May 2011 19:14
#449088
make sure you use a botteming/flat ended tap B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum