Front bevel drive questions

  • bls5050
  • bls5050's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 34
  • Thanks: 2

Front bevel drive questions

05 May 2011 20:56
#449111
So I was bolting on the front bevel drive, and I broke one of the bolts. It's the center of the three front bolts that hold the unit onto to side of the transmission. It broke off just below the surface that it threads into. So I said to myself, I said "self, we can fix this in about 10 minutes, this is nothing to stress over." So I went and got a drill, a bit, and an easy out. Punched a center-mark on the end that I could see, drilled a hole, tapped the easy-out into it, and broke the easyout flush with the surface. Shiiiiiiit! So here's the situation: I can't get this thing out. I can't get the drill bit to bite into the hardened easy-out without tearing up the gasket surface.

I perused my not-so-vast collection of tools looking for a solution, and I think I might be able to take a slightly holistic approach...you know, not really solving the problem, just co-existing with it. If i leave the end of the bolt, with the end of the easy-out stuck in it, right where it's at, and use some Permatex Ultra Copper RTV to seal the gasket, will this suffice to seal this seam from leakage? Does this seem like a reasonable idea, or are there other suggestions?

My other question is, while I was in there, right before I broke the afore-mentioned bolt, I noticed that the clutch release lever doesn't work when the bevel drive is bolted in place. It operates freely when the unit is unbolted, but it seems stuck when bolted up. Is this a normal condition at this stage of reassembly? Or should the clutch push-rod be pushing when the lever is pulled?
1980 KZ1000st

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: Front bevel drive questions

05 May 2011 21:03
#449115
can you get your hands on a good left handed drill bit? B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • bls5050
  • bls5050's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 34
  • Thanks: 2

Re: Front bevel drive questions

05 May 2011 21:16
#449116
Not locally. I've looked a couple times in the past. I can't drill into it with a hand drill. It's kind of a jagged break. There's not much to work with, it's a 6mm bolt.
1980 KZ1000st

Please Log in or Create an account to join the conversation.

  • Nebr_Rex
  • Nebr_Rex's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1889
  • Thanks: 295

Re: Front bevel drive questions

05 May 2011 22:49
#449129
Take it to your local welding shop and have them weld a harded nut to what you have stuck in that hole.
This will do 3 things.

1)It will heat up the cases and maybe break the bolt lose.

2)It will give you something to grip with a wrench.

3)You can tap on the nut like an impact driver to help break it loose.
2002 ZRX1200R
81 GPz1100
79 KZ1000st daily ride
79 KZ1000mk2 prodject
78 KZ650sr
78 KZ650b
81 KZ750e
80 KZ750ltd
77 KZ400/440 cafe project
76 KZ400/440 Fuel Injected

www.dotheton.com/index.php?threads/dr-je...air-of-kz400s.39120/


.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum