At wit's end.

  • KZ1979LTD
  • KZ1979LTD's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 53
  • Thanks: 2

At wit's end.

07 May 2011 22:47
#449495
KZ Guru's HELP me!
I recently decided to check the valve clearances on my bike. (1979 LTD with about 27,000 miles) Several were out of spec and I replaced them to get it within tolerance. I also decided to run through the carbs since the bike was down for a while waiting on new shims. I synched the throttle valves setting them at the 0.7mm in the manual. I used the clear tube method to set the float heights correctly. I turned the pilot screws in all the way and then backed each one out 2 and a half turns. The bike has a 4 into 1 Yosh on it and the original airbox. I also removed all the smog crap last summer and closed it off. The bike was running ok before I changed the shims and adjusted the carbs but now it runs like crap. Would changing the shims throw the bikes timing off? It won't start or run without the choke half in, and when I try to give it throttle it hits about 2500 rpms and bogs down. It sounds like it's not hitting on all 4 cylinders and when the rpm's drop below 1000 it knocks alot and finally dies. The bike does have the original points and condenser. What did I do? Any input would be appreciated.

Please Log in or Create an account to join the conversation.

  • roy-b-boy-b
  • roy-b-boy-b's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 3245
  • Thanks: 103

Re: At wit's end.

07 May 2011 22:53
#449497
I would be looking at the carbs. Your air mixture seems out too much. roy
1979 LTD Street Fighter.1977 KZ1000

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: At wit's end.

07 May 2011 22:55
#449498
id start 1 1/2 turns out and tune from there B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • kopcicle
  • kopcicle's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 37
  • Thanks: 4

Re: At wit's end.

08 May 2011 01:18
#449516
Order of operation
adjust valves
adjust dwell
set timing
sync carbs
adjust idle mixture

do you want to know more ?

~kop
"There are two major pressure changes in a four stroke internal combustion engine , when you light the fire and when the rods exit the block..."

Please Log in or Create an account to join the conversation.

  • mjg15
  • mjg15's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 698
  • Thanks: 18

Re: At wit's end.

08 May 2011 02:37
#449532
Knocks at low RPM? Check for stuck advancer and vacuum leaks at intake manifolds.
'80 Z750fx
'81 KZ550A
'81 GPz550's, Too many!
'82 KZ1000R
'82 GPz750
'90 ZR550


Project photo album: s163.photobucket.com/albums/t289/mg15_ph...GPz-ZR550%20project/
s163.photobucket.com/albums/t289/mg15_ph...current=DSC01286.jpg

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum