Rebuilt Engine... First Ride... Died... Won't Run

  • tyhoppy
  • tyhoppy's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 21
  • Thanks: 0

Rebuilt Engine... First Ride... Died... Won't Run

08 May 2011 23:35
#449742
Ok. I rebuilt my 81 KZ1000 and it started up fine, so I took it for the first test ride. I made it between two and three miles and it died on me. The bike didn't want to idle, which I'm not sure is related. But, it shut off and wouldn't start. I attempted to push start it and it ran for a few seconds and when I opened the throttle is backfired through what seemed like all of the carbs; then it died and wouldn't start.

I got the bike home and number 1 and 4 cylinders have spark and they both have between 120-135 psi. After a lot of rolling the bike over, the spark plugs from those cylinders didn't get wet. I have gas getting to the connection at the center of the carburetors, I'm not sure what to check next? I blew air through the carbs at that connection to try to clear any dirt stuck in the float, but that didn't help.

Any suggestions?

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Rebuilt Engine... First Ride... Died... Won't Run

08 May 2011 23:51
#449747
tyhoppy wrote: ...rebuilt my 81 KZ1000 and it started up fine, so I took it for the first test ride. I made it between two and three miles and it died on me. The bike didn't want to idle, which I'm not sure is related. But, it shut off and wouldn't start. I attempted to push start it and it ran for a few seconds and when I opened the throttle is backfired through what seemed like all of the carbs; then it died and wouldn't start.
...number 1 and 4 cylinders have spark and they both have between 120-135 psi. After a lot of rolling the bike over, the spark plugs from those cylinders didn't get wet. I have gas getting to the connection at the center of the carburetors, I'm not sure what to check next? I blew air through the carbs at that connection to try to clear any dirt stuck in the float, but that didn't help.
Any suggestions?

Would double-check that valve clearances are within specs.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • tyhoppy
  • tyhoppy's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 21
  • Thanks: 0

Re: Rebuilt Engine... First Ride... Died... Won't Run

08 May 2011 23:56 - 08 May 2011 23:57
#449749
That was my first thought, but those two cylinders that I know have good compression must have valve clearances within spec, am I right? So, wouldn't they have wet plugs if it were getting fuel?
Last edit: 08 May 2011 23:57 by tyhoppy.

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Rebuilt Engine... First Ride... Died... Won't Run

09 May 2011 00:09
#449755
tyhoppy wrote: That was my first thought, but those two cylinders that I know have good compression must have valve clearances within spec, am I right? So, wouldn't they have wet plugs if it were getting fuel?

The reported symptoms sound like cold engine's compression is lost upon engine attaining operating temperature due to insufficient valve clearance.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • mjg15
  • mjg15's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 698
  • Thanks: 18

Re: Rebuilt Engine... First Ride... Died... Won't Run

09 May 2011 02:03
#449792
Patton wrote:
tyhoppy wrote: That was my first thought, but those two cylinders that I know have good compression must have valve clearances within spec, am I right? So, wouldn't they have wet plugs if it were getting fuel?

The reported symptoms sound like cold engine's compression is lost upon engine attaining operating temperature due to insufficient valve clearance.

Good Fortune! :)

That happened on my 750/4. It would start and idle, but after a while it would randomly drop cylinders. It showed 120 psi cold, I never checked it hot. most of the valves had .000 to .001 clearance. Somebody did the math wrong. I got it cheap because it had mysterious "carb" problems.
'80 Z750fx
'81 KZ550A
'81 GPz550's, Too many!
'82 KZ1000R
'82 GPz750
'90 ZR550


Project photo album: s163.photobucket.com/albums/t289/mg15_ph...GPz-ZR550%20project/
s163.photobucket.com/albums/t289/mg15_ph...current=DSC01286.jpg

Please Log in or Create an account to join the conversation.

  • jeffasaki
  • jeffasaki's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 996
  • Thanks: 44

Re: Rebuilt Engine... First Ride... Died... Won't Run

09 May 2011 03:20
#449796
Get some BRAND NEW NGK Iridium sparkplugs
If not already done put $10.00 of new high octane gas in the tank
Charge the battery
Headlight off full choke no throttle
in netral give er a good full spark crank (I bet she starts)
Let it run till it gets hot.(smoke from the pipes will leave after a few warm ups)
CHANG OIL 10w40 for summer
FRAM ch6013 for a 78 1000
All 4 pilot air screws should be between 1&1/4 to 2 urns out
THE SMOKE AT STARTUP IS CAUSED buy old valve stem seals and really isnt a critical point of failure,
check tire pressures 30psi front and 28psi rear is what I run
LET IT SIT OVERNIGHT WITH FRESH FUEL IN THE CARBS!!!!!
Wake up have a red bull and 7 coffees then go for a ride.
CHEERS JEFFASAKI
78 Z1R
78 KZ1000
76 KH500 gone
71 HS1B 90
81 GS 1100 gone
80 PE400
02 KLR


Ontario Canada

Please Log in or Create an account to join the conversation.

  • jeffasaki
  • jeffasaki's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 996
  • Thanks: 44

Re: Rebuilt Engine... First Ride... Died... Won't Run

09 May 2011 03:29
#449798
ALSO CHECK YOUR MECHANICAL IGNITION ADVANCER
2 weights that fly apart from each other behind what I hope is a dyna ingnition but could be points asa well
If you are running points you deserve whay you get
if youare running a dyna then check your mechanical advancer behind the timming plate a sshot of oil works wonders
78 Z1R
78 KZ1000
76 KH500 gone
71 HS1B 90
81 GS 1100 gone
80 PE400
02 KLR


Ontario Canada

Please Log in or Create an account to join the conversation.

  • jeffasaki
  • jeffasaki's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 996
  • Thanks: 44

Re: Rebuilt Engine... First Ride... Died... Won't Run

09 May 2011 03:35
#449800
ALSO CHECK WIRES comming fro front left alternater somtimes they short out under the output shaft cover
78 Z1R
78 KZ1000
76 KH500 gone
71 HS1B 90
81 GS 1100 gone
80 PE400
02 KLR


Ontario Canada

Please Log in or Create an account to join the conversation.

  • jeffasaki
  • jeffasaki's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 996
  • Thanks: 44

Re: Rebuilt Engine... First Ride... Died... Won't Run

09 May 2011 03:43
#449802
ALSO CHECK FOR A BAD GOUND any electrical connection that looksw green needs to be cleaned with a piece of emery clth or your teeth
\or whatever gets the job done
78 Z1R
78 KZ1000
76 KH500 gone
71 HS1B 90
81 GS 1100 gone
80 PE400
02 KLR


Ontario Canada

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Rebuilt Engine... First Ride... Died... Won't Run

09 May 2011 03:57 - 09 May 2011 04:02
#449805
tyhoppy wrote: Ok. I rebuilt my 81 KZ1000 and it started up fine, so I took it for the first test ride. I made it between two and three miles and it died on me. The bike didn't want to idle, ///// After a lot of rolling the bike over, the spark plugs from those cylinders didn't get wet.
If you have no gas feeding the carbs running two cylinders, it isn't going to run worth crap.

A flaky coil will act up after a few miles and take out two cylinders.

Definitely check the mechanical advancer since most of them are flaky to some degree.
1979 KZ-750 Twin
Last edit: 09 May 2011 04:02 by bountyhunter.

Please Log in or Create an account to join the conversation.

  • dynastydudge
  • dynastydudge's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 53
  • Thanks: 0

Re: Rebuilt Engine... First Ride... Died... Won't Run

09 May 2011 11:25
#449835
make sure you dont have the plug wires crossed on those two cylinders that arnt hitting.
were not here for a long time, just a good time......1980 kz750 ltd h1
1982 honda cm 450e

Please Log in or Create an account to join the conversation.

  • tyhoppy
  • tyhoppy's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 21
  • Thanks: 0

Re: Rebuilt Engine... First Ride... Died... Won't Run

09 May 2011 13:50
#449850
I know it won't run worth crap without fuel going to two cylinders...


This is why I posted the question. What would cause the no fuel issue? I stated it has fuel to the carbs...

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum