Starter Clutch Question
- The Milkman
-
Topic Author
- Offline
- User
-

Registered
- Posts: 794
- Thanks: 194
Starter Clutch Question
17 May 2011 23:59
Ok, I finally got my starter clutch apart by using a strap oil filter wrench. Thanks for the help Wireman

When I took the snap ring off the other end and pulled it apart, I noticed the rubber block inside were deteriorating a little. Not a lot, just a little on the edges and corners. Is there any replacements for them. I haven't been able to find any yet. I was wondering if fuel line hose cut to length would work in there.
Any ideas?
The old ones are getting a little brittle but they still flex.
Thanks,
Les
When I took the snap ring off the other end and pulled it apart, I noticed the rubber block inside were deteriorating a little. Not a lot, just a little on the edges and corners. Is there any replacements for them. I haven't been able to find any yet. I was wondering if fuel line hose cut to length would work in there.
Any ideas?
The old ones are getting a little brittle but they still flex.
Thanks,
Les
78 650-C2, Stock engine, Jardine 4-2 Exh., 17-38 sprockets, dyna ignition and coils, coil wiring mod, carb mod.
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Starter Clutch Question
18 May 2011 10:08
Are you Talking about Item #7 in this Picture?
If so then 13098-029 DAMPER RUBBER looks to be a good # and $6-7 ea X 8 needed.
If so then 13098-029 DAMPER RUBBER looks to be a good # and $6-7 ea X 8 needed.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- The Milkman
-
Topic Author
- Offline
- User
-

Registered
- Posts: 794
- Thanks: 194
Re: Starter Clutch Question
18 May 2011 22:45 - 18 May 2011 22:46
Yes I is.
And thanks for the info.
Les
And thanks for the info.
Les
78 650-C2, Stock engine, Jardine 4-2 Exh., 17-38 sprockets, dyna ignition and coils, coil wiring mod, carb mod.
Last edit: 18 May 2011 22:46 by The Milkman.
Please Log in or Create an account to join the conversation.
- The Milkman
-
Topic Author
- Offline
- User
-

Registered
- Posts: 794
- Thanks: 194
Re: Starter Clutch Question
20 May 2011 00:26
Well, the blocks are discontinued at all of the places I have found on the web. Anymore ideas????
Thanks,
Les
Thanks,
Les
78 650-C2, Stock engine, Jardine 4-2 Exh., 17-38 sprockets, dyna ignition and coils, coil wiring mod, carb mod.
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: Starter Clutch Question
20 May 2011 00:39
ill check in the morning for ya
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Starter Clutch Question
20 May 2011 00:54 - 20 May 2011 00:55
Maybe the list of models will help out.
I don't see where to get new ones either, how bad are yours?
I don't see where to get new ones either, how bad are yours?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 20 May 2011 00:55 by Motor Head.
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: Starter Clutch Question
20 May 2011 00:57
would it make any differance to flip them 180 degrees end for end?
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Starter Clutch Question
20 May 2011 01:04 - 20 May 2011 12:14
These guys list it, this is where I got the first picture. A free phone call will be a good way to see if there is a way to source them.
www.cyclepartsnation.com/pages/OemParts#...50-H3-1983/070087I-9
You can call Z1 as well if you haven't already.
Even my local Dealer shows them as a good # on-line, I can call and ask them . Just did and No, they cannot source them. Never carried them in stock either. Suggested whats already been tried, Google.
www.cyclepartsnation.com/pages/OemParts#...50-H3-1983/070087I-9
You can call Z1 as well if you haven't already.
Even my local Dealer shows them as a good # on-line, I can call and ask them . Just did and No, they cannot source them. Never carried them in stock either. Suggested whats already been tried, Google.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 20 May 2011 12:14 by Motor Head.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
