cam and valve clearances

  • fstphil66
  • fstphil66's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 8
  • Thanks: 0

cam and valve clearances

21 May 2011 01:27
#452510
Hey Guys ,How you all doing? My name is Phil and I own a 98 kz1000p.
I'm doing the top end over w/ a 1075 kit.I have a head from a 82 kzp that I am having done for the motor.I bought a set of 82 gpz cams off of e-bay and they turned out to be a pretty lumpy after market camset(.366-.377 each has an H and one has R5 and the other has R7 in raised letters on them)
Anybody have any idea's on what kind they are? Has anybody run cams this size in their kz1000? Are these things streetable? Will I have any problems with piston clearance on the valves? What springs should I use?
I'm sure there are gonna be many more questions for you guys before this project is over ,so Thankx in advance for all the help,
Phil

Please Log in or Create an account to join the conversation.

  • nads.com
  • nads.com's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 993
  • Thanks: 20

Re: cam and valve clearances

21 May 2011 03:17
#452520
Not sure who makes those cams but they are just right for your motor. A.P.E. makes the springs you will need. The cams either bolt in or have to be degreed. You'll have to find out before you put them in and valve clearance will not be a problem. Someone on this board will probly know what cams you have.

Please Log in or Create an account to join the conversation.

  • mark1122
  • mark1122's Avatar
  • Offline
  • User
  • User
    Registered
  • Keep twisting it
  • Posts: 5297
  • Thanks: 109

Re: cam and valve clearances

21 May 2011 08:23
#452530
Those are not what u would call big cams by any means so dont be worried about them. :)
u can put a dab playdoe in the valve pockets,then put the old head gasket and head and cams in . turn the motor over by hand, then take it apart and measure the new thickness of the playdoe. now u know the v to p clearance.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.

~ ~ ~_@
~ ~ _- \,
~ (k) / (z)

Please Log in or Create an account to join the conversation.

  • andy9802gt
  • andy9802gt's Avatar
  • Offline
  • User
  • User
    Registered
  • If it tastes that good, eat it yourself.
  • Posts: 695
  • Thanks: 19

Re: cam and valve clearances

21 May 2011 08:48
#452533
Those are barely over stock lift I think plenty streetable. I run .410 cams, my little brother runs .435in/.410ex, and I know there are guys here running bigger than that on the street. And degree them if for no other reason than getting the best possible timing you can.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm

Please Log in or Create an account to join the conversation.

  • DoubleDub
  • DoubleDub's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: cam and valve clearances

21 May 2011 18:09
#452603
For example, the Web Cam Grind 118 (smallest lift cam for drop in street performance) is .365/.365.

www.webcamshafts.com/pages/motorcycle/ka...c_001730_002566.html

I believe the lift where you need to start clearancing the head is around .385(?) - always best to check by rotating everything by hand first.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum