issue with... starting motor?
- murr50
-
Topic Author
- Offline
- User
-

Registered
- Posts: 105
- Thanks: 3
issue with... starting motor?
21 May 2011 20:02
After replacing my piston rings, today i reassembled my engine. When i tried to start it, it turned over fine for a while but as i held the stareted button for a few seconds it seemed to start slipping. the little crank on the ignition would stop spinning, but i could hear the starter motor still doing its thing... does anyoneknow what might be happening?
1977 kz650 C
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: issue with... starting motor?
21 May 2011 20:13
starter clutch might be slipping,or you knocked the woodruff key off of crank if its a z1 .what kind of bike?
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- murr50
-
Topic Author
- Offline
- User
-

Registered
- Posts: 105
- Thanks: 3
Re: issue with... starting motor?
21 May 2011 20:18
its a 77 kz650.. its strange though, this never happened before, then i put the bike back together and it started happeneing... it doesnt do it right away, it takes a few seconds
1977 kz650 C
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: issue with... starting motor?
21 May 2011 20:20
motor is tighter,with more compression now so its harder to turn over.
where is timing set at?
where is timing set at?
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- murr50
-
Topic Author
- Offline
- User
-

Registered
- Posts: 105
- Thanks: 3
Re: issue with... starting motor?
21 May 2011 20:24
my ignition timing? im currently having issues with that as well.. im not entirely sure how to correctly set it.
my cam timing is set properly as far as i know.. if it isnt im sure i have much larger issues
my cam timing is set properly as far as i know.. if it isnt im sure i have much larger issues
1977 kz650 C
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: issue with... starting motor?
21 May 2011 20:26
oh boy,start at the beginning.
when did the problem start? personally most of my problems started shortly after birth! :blink: :woohoo:
when did the problem start? personally most of my problems started shortly after birth! :blink: :woohoo:
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- murr50
-
Topic Author
- Offline
- User
-

Registered
- Posts: 105
- Thanks: 3
Re: issue with... starting motor?
21 May 2011 20:31
hahaha alright, so i took the bike apart over the winter, replaced gaskets, piston rings etc (bike started and ran fine last summer) now after putting the bike back together, it wont quite start.. this i believe is because of 2 things. First, im not sure how to properly time the ignition (dyna) and second, the starter motor sounds like it slips after about 5 seconds of holding the starter.. does that clear things up at all?
1977 kz650 C
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: issue with... starting motor?
21 May 2011 20:35
www.kz650.info
might be able to answer your questions. Also weight and type of oil being used? Some car rated oils contain friction modifiers not compatable with starter and wet clutches on these bikes.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: issue with... starting motor?
21 May 2011 20:38
yep,got that part.
its the part where you mentioned questionable cam timing that scared me. :laugh:
try backing ignition timing off a couple degrees to see if it will turn over easier
its the part where you mentioned questionable cam timing that scared me. :laugh:
try backing ignition timing off a couple degrees to see if it will turn over easier
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- murr50
-
Topic Author
- Offline
- User
-

Registered
- Posts: 105
- Thanks: 3
Re: issue with... starting motor?
21 May 2011 20:40
its a 10w40 oil, i will have to check what make it is though, i forget
1977 kz650 C
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: issue with... starting motor?
21 May 2011 20:40
Running the starter for an extended period isn't a good idea. Figure out how to set the timing first. Then start the bike using the kicker. A properly tuned '77 KZ650 should start with no more than 3 or 4 kicks (hopefully 1 or 2). After you get it running properly move on to the starter issue. You may find the starter works fine when you don't need to crank it for extended periods. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- murr50
-
Topic Author
- Offline
- User
-

Registered
- Posts: 105
- Thanks: 3
Re: issue with... starting motor?
21 May 2011 20:47
does anyone have any further instruction on timing my ignition? i must be confused at the instructions given on the dyna website...
1977 kz650 C
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
