Regarding GPZ 750 cam timings....

  • ELCouz
  • ELCouz's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 376
  • Thanks: 5

Regarding GPZ 750 cam timings....

22 May 2011 13:07 - 06 Sep 2014 08:01
#452782
Dear KZ enthusiasts,

I'm a owner of a 1982 GPZ 750 (20k miles) and i have a question regarding the cam timing.

When changing the head gasket, i have seen a deep scratch on one of my cylinder wall (broken ring).
I didn't have the choice but to get the four cylinders bored oversize for the Wiseco K810 kit (least expensive solution).

I've totally blown my budget on this bike (1400$ total cost on the engine, mill head/cylinders + wiseco kit + boring + valve job) to get her running again. Well i could have bought a more recent bike but i really like this vintage bike .

Okay here's my question :

I've been told many times, if the head is milled i must need to get the cam sprocket machined to make them adjustable for the timing...

Will the bike run without doing that ? I can't afford to mess with that (could be costly mistake, 1400$ down the toilet) or to get it machined again... The head/cylinders as been milled (resurfaced) to get it straight ( i don't know by how much but the guy told me it was almost perfectly straight before.)

Degree will be off ? If so by how much approx.? and is it enough to get incorrect timing like detonation (pinging)... Seriously, i don't care about max HP. I just want to ride her again before i completely miss the riding season :)


Thank you very much!
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe
Last edit: 06 Sep 2014 08:01 by ELCouz.

Please Log in or Create an account to join the conversation.

  • ELCouz
  • ELCouz's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 376
  • Thanks: 5

Re: Regarding GPZ 750 cam timings....

22 May 2011 21:44
#452878
update: after many internet searches I'm confused...

Some says it must be done others say i should not bother with cam timing especially if light milling has been done (scuff/scratch removal)...

Anybody have experience and understanding of an engine timing?

I'm kind of new to this... and engine is now out of factory specification (bored to 810cc) so i don't think i can follow tips from the Kawasaki manual.

Have a nice day,

Laurent
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe

Please Log in or Create an account to join the conversation.

  • Nebr_Rex
  • Nebr_Rex's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1889
  • Thanks: 295

Re: Regarding GPZ 750 cam timings....

22 May 2011 22:05
#452891
Had a 440 head milled .030 and retarded the cam 2/3 of a tooth.
Which equals out to about 10*.
Check you cam timing against what stock is.
When ever you mill an over head cam engine it will retard the cam.
How much did you have it milled?
2002 ZRX1200R
81 GPz1100
79 KZ1000st daily ride
79 KZ1000mk2 prodject
78 KZ650sr
78 KZ650b
81 KZ750e
80 KZ750ltd
77 KZ400/440 cafe project
76 KZ400/440 Fuel Injected

www.dotheton.com/index.php?threads/dr-je...air-of-kz400s.39120/


.

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: Regarding GPZ 750 cam timings....

22 May 2011 22:12
#452896
you can elongate the slots in cam gears with a rat tail or chain saw file,no need to buy aftermarket gears.(yes ive personally done this many times on 900/1000 bikes,not on a 650 with 750 sleeves with 810 kit in a stock 650 block though! )
its not always needed,depends on how far out of time the cams are and how picky you are.
do you have access to a cam degreeing wheel? B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • ELCouz
  • ELCouz's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 376
  • Thanks: 5

Re: Regarding GPZ 750 cam timings....

22 May 2011 22:16
#452899
How much did you have it milled?

.005 this is what the guy (CVTech AAB) told me.

Btw, how i can measure the head thickness? To check if the head has been milled already by Previous Owner™ ...

i don't have received the cylinder + head yet (wiseco piston kit back-ordered)

I'm just wondering before i get the whole expensive thing what needs to be check and done !

best regards,
laurent
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe

Please Log in or Create an account to join the conversation.

  • ELCouz
  • ELCouz's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 376
  • Thanks: 5

Re: Regarding GPZ 750 cam timings....

22 May 2011 22:18 - 22 May 2011 22:20
#452900
do you have access to a cam degreeing wheel?

No unfortunately :(

I don't know anybody engine savvy beside on this forum B) ... but you are all away from me :(

laurent


EDIT: Can timing be done by ear and/or guess and/or without a degreeing wheel ?
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe
Last edit: 22 May 2011 22:20 by ELCouz.

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: Regarding GPZ 750 cam timings....

22 May 2011 22:30
#452905
ELCouz wrote:
do you have access to a cam degreeing wheel?

No unfortunately :(

I don't know anybody engine savvy beside on this forum B) ... but you are all away from me :(

laurent


Cam timing be done by ear and/or guess ?
well timing cams by ear is normally followed by the sound of valves either hitting each other or being thumped by a piston as you try and rotate motor,neither is a good thing! :laugh:
one way to compensate for overly milled head would be to figure out how high the highest piston sits in its bore and use a thicker base gasket or spacer under the block to make up for some of the material milled from head(probably from block also).
this will drop your compression just a little which will make it easier to run on pump gas anyway,and it will also gain you a little piston to valve clearance.
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • Nebr_Rex
  • Nebr_Rex's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1889
  • Thanks: 295

Re: Regarding GPZ 750 cam timings....

22 May 2011 22:33
#452907
ELCouz wrote:
How much did you have it milled?

.005 this is what the guy (CVTech AAB) told me.

Btw, how i can measure the head thickness? To check if the head has been milled already by Previous Owner™ ...

i don't have received the cylinder + head yet (wiseco piston kit back-ordered)

I'm just wondering before i get the whole expensive thing what needs to be check and done !

best regards,
laurent

.005 is nothing.
The increased displacement and compression will more than make up for it.
Just reassemble per your manual.
To check your head thickness measure from deck surface to the top where the cam cover bolts to.
2002 ZRX1200R
81 GPz1100
79 KZ1000st daily ride
79 KZ1000mk2 prodject
78 KZ650sr
78 KZ650b
81 KZ750e
80 KZ750ltd
77 KZ400/440 cafe project
76 KZ400/440 Fuel Injected

www.dotheton.com/index.php?threads/dr-je...air-of-kz400s.39120/


.

Please Log in or Create an account to join the conversation.

  • ELCouz
  • ELCouz's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 376
  • Thanks: 5

Re: Regarding GPZ 750 cam timings....

22 May 2011 23:08
#452921
well timing cams by ear is normally followed by the sound of valves either hitting each other or being thumped by a piston as you try and rotate motor,neither is a good thing!

So i guess that a degreeing wheel is a must unless i have a spare engine lying around :P

.005 is nothing.
The increased displacement and compression will more than make up for it.
Just reassemble per your manual.
To check your head thickness measure from deck surface to the top where the cam cover bolts to.

Thanks for the info. I will double check everything once i receive the engine :)
you can elongate the slots in cam gears with a rat tail or chain saw file

Isn't that dangerous ? i mean wont the bolts have a chance to slide with all that engine vibration and sudden torque ?


laurent
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: Regarding GPZ 750 cam timings....

22 May 2011 23:18
#452924
its no differant than slotted aftermarket sprockets B)
.005 isnt much untill you find out somebody took .010 off of it previously and if the block has been milled on top of it you start running into issues B)
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • wireman
  • wireman's Avatar
  • Offline
  • User
  • User
    Registered
  • The most interesting prick in the world
  • Posts: 4736
  • Thanks: 299

Re: Regarding GPZ 750 cam timings....

22 May 2011 23:22
#452927

Attachment sprockets.jpg not found


heres a picture of aftermarket slotted sprockets,youre doing the same thing but using stock sprockets.
but by all means ill wait for the 650/810 building experts to explain why guys have been doing it the wrong way for 40 plus years(before my building days) :laugh:
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.

Please Log in or Create an account to join the conversation.

  • Nebr_Rex
  • Nebr_Rex's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1889
  • Thanks: 295

Re: Regarding GPZ 750 cam timings....

22 May 2011 23:49
#452933
wireman wrote: its no differant than slotted aftermarket sprockets B)
.005 isnt much untill you find out somebody took .010 off of it previously and if the block has been milled on top of it you start running into issues B)

+1
Mock things up by installing pistons without the rings an set your block with base gasket.
Measure the difference with a fealer gauge.
You can get an idea of your deck clearence.
Add that to what your compressed head gasket thickness should be for the piston to head clearence.

And take the head,turn it upside down,place the head gasket and mark the bore.
Remove the gasket and take a piston,place it on your mark,intake valve pocket to intake valve.
Move piston in a circular motion to see if any interference there.
Piston to valve clearence should not be a problem with GPZ cams and Wiseco pistons.
These methods might seem crude but they should get you back on the road since your doing no more than a big bore.
2002 ZRX1200R
81 GPz1100
79 KZ1000st daily ride
79 KZ1000mk2 prodject
78 KZ650sr
78 KZ650b
81 KZ750e
80 KZ750ltd
77 KZ400/440 cafe project
76 KZ400/440 Fuel Injected

www.dotheton.com/index.php?threads/dr-je...air-of-kz400s.39120/


.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum