81 kz1100 spectre D2 Valves/compression

  • morhaven
  • morhaven's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 77
  • Thanks: 0

81 kz1100 spectre D2 Valves/compression

31 May 2011 15:15
#454527
Hi I need some advise.
81 kz1100 spectre D2

I do a leak down test on all 4 cylinders and all less than 5% @ TDC
I check compression 120 PSI all 4 cylinders.

I start the bike idles well all 4 cylinders, but then when warming up 1-2min it only runs on cylinder 3-4.
Cylinder 1-2 not working..well only if full throttle it seems.

Still have spark form all coils. Carbs are cleaned and adjusted.

I re-check compression on Cylinder 1-2 I have 60psi Throttle closed.. open Throttle 120Psi.
Compression on 3-4 120 Psi throttle Open or closed.

So I assume this is sticking vavles, I sprayed Foggin oil in both intake of carb 1 and 2.. will see what that does. Next will re-do leakdown after another try .

Do you agree with sticking valves? any tips I should try to unstick them if this is the case?

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: 81 kz1100 spectre D2 Valves/compression

31 May 2011 15:29 - 01 Jun 2011 23:27
#454532
morhaven wrote: Hi I need some advise.
81 kz1100 spectre D2

I do a leak down test on all 4 cylinders and all less than 5% @ TDC
I check compression 120 PSI all 4 cylinders.

I start the bike idles well all 4 cylinders, but then when warming up 1-2min it only runs on cylinder 3-4.
Cylinder 1-2 not working..well only if full throttle it seems.

Still have spark form all coils. Carbs are cleaned and adjusted.

I re-check compression on Cylinder 1-2 I have 60psi Throttle closed.. open Throttle 120Psi.
Compression on 3-4 120 Psi throttle Open or closed.

So I assume this is sticking valves, I sprayed Foggin oil in both intake of carb 1 and 2.. will see what that does. Next will re-do leakdown after another try .

Do you agree with sticking valves? any tips I should try to unstick them if this is the case?

Would check valve clearances to assure all are within factory specs.

Where valve has some minimal clearance, too tight valve clearance may not be indicated by compression test or leak-down test.

The minimal clearance becomes zero clearance as the engine attains normal operating temperature, and the valve then fails to fully seat, causing loss of compression at normal operating temperature.

Good Fortune! :)
1973 Z1
KZ900 LTD
Last edit: 01 Jun 2011 23:27 by Patton.

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: 81 kz1100 spectre D2 Valves/compression

31 May 2011 15:29 - 31 May 2011 15:30
#454533
Patton beat me to it!! :laugh:
Check Valve clearance. Adjust to spec. Shim on top so it is pretty easy with the tool. You might be able to swap a couple of shims around, and only buy a couple.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 31 May 2011 15:30 by Motor Head.

Please Log in or Create an account to join the conversation.

  • steell
  • steell's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6849
  • Thanks: 208

Re: 81 kz1100 spectre D2 Valves/compression

31 May 2011 19:33 - 31 May 2011 19:35
#454589
First off, a comp check with the throttle closed is useless.
Second, the only way "Compression on 3-4 120 Psi throttle Open or closed." could happen is if you have no carbs mounted on those two cylinders. Just totally defies physics.

So, before you "assume" anything, go back and do a proper compression test.



Set the service fuel level in the float bowls for 1&2, and you may need new float valves.
KD9JUR
Last edit: 31 May 2011 19:35 by steell.

Please Log in or Create an account to join the conversation.

  • morhaven
  • morhaven's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 77
  • Thanks: 0

Re: 81 kz1100 spectre D2 Valves/compression

01 Jun 2011 15:11
#454792
It was only by reading this forum that I found out I needed to open throttle for proper compression test.

I will re-check that is why I write on this forum for assistance..
and then depending,Might as well check Valve clearances, from what I see just need to pop valve cover off and use feeler gauge

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum