carb
- french
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
carb
04 Jun 2011 12:38
i have a 1989 kz1000 police. i have changed the sprockets and chain so i have a higher gear ratio. i go 70 mph at 3500 rpms. the problem i have is i dont go past 1/4 throttle at that speed. when i try to accelerate the motor pings real bad. when i pull out the enricher the pinging stops. does it sound like i need larger pilot jets?
1989 kz1000p
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: carb
04 Jun 2011 12:41
No, it sounds like you need to raise the needle up a notch on the slides.
Are you using a stock airbox, or pod/individual filters?
Are you using a stock airbox, or pod/individual filters?
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- french
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: carb
04 Jun 2011 12:57
OK - Should run correctly then. Have you changed or affcted the mixture screws on the carbs?
Do you know what they are set at - tuned?
Do you know what they are set at - tuned?
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- french
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
Re: carb
04 Jun 2011 12:59
not really sure what they are set at. what is a good starting point?
1989 kz1000p
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: carb
04 Jun 2011 13:06
The stock setting is 1.25 turns out from lightly seated (dont crank'em down). You can use 1.5 as a good starting point as well with that K&N filter.
Your screws are mixture type. That means they add fuel (richen) the mix when loosened out (counter-clockwise), and lean things out when turned in.
Your screws are mixture type. That means they add fuel (richen) the mix when loosened out (counter-clockwise), and lean things out when turned in.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- french
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
Re: carb
04 Jun 2011 13:11
i will see what they are set at. if they are out more then 1.25 turns already should i turn them out more? if so how far out can i go safely?
1989 kz1000p
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: carb
04 Jun 2011 13:19 - 04 Jun 2011 13:35french wrote: i will see what they are set at. if they are out more then 1.25 turns already should i turn them out more? if so how far out can i go safely?
you can continue to turn them out as far as you like - it will not damage anything. There will however be a point when it will become too rich, and the idle/engine will begin to stumble.
A basic way to tune those screws is to turn them to the highest idle point. If that is not detectable by ear, then turn them in till the engine stumbles (too lean), then turn them out (counting the turns) till the engine stumbles again. Then turn them back in to half of your turn count - right in between the too rich/too lean point, and your good to go.
Done usually at idle 1000rpm, once engine is hot, and with a big fan pointed at the headers.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Last edit: 04 Jun 2011 13:35 by TeK9iNe.
Please Log in or Create an account to join the conversation.
- french
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
Re: carb
04 Jun 2011 13:21
i will give that a try. if i try this and the problem still exist should i raise the needle jet like you said?
1989 kz1000p
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: carb
04 Jun 2011 13:37 - 04 Jun 2011 13:40french wrote: i will give that a try. if i try this and the problem still exist should i raise the needle jet like you said?
Yes, most deffinately. The mixture screw adjsutment most likely not solve your issue, but it is an easier first step to properly tuned carbs.
I would go ahead with raising the needle anyways, as it makes to most difference in the throttle range you describe, and will most likey give you the result you desire without much tuning required.
Good luck.
Have you performed all your basic maintenence? Like adjusting the valve lash, etc.???
A good service manual is worth its weight in silver.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Last edit: 04 Jun 2011 13:40 by TeK9iNe.
Please Log in or Create an account to join the conversation.
- french
-
Topic Author
- Offline
- User
-

Registered
- Posts: 11
- Thanks: 0
Re: carb
04 Jun 2011 13:40
thank you for your help. i will have to order shims for the needle jets from z1. i will post my results when i get the shims.
1989 kz1000p
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: carb
04 Jun 2011 13:46
The jet needles may have grooves already, which means you can simply move the clip down one position. Best to check first.
Also, any little half mm washers will do, just be sure to check them with a dial caliper/micrometer, and pick ones that are identicl values.
Also, any little half mm washers will do, just be sure to check them with a dial caliper/micrometer, and pick ones that are identicl values.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
