Z1 oil cooler

  • luc
  • luc's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 78
  • Thanks: 1

Z1 oil cooler

05 Jun 2011 15:43 - 05 Jun 2011 17:11
#455616
Any idea why all the after-market cooler oil fittings adaptors are 1/4" pipe and the coolers are designed for 3/8" or -6 hose when the factory original was quite bigger?
The ID on after-market fittings is just slightly more than 1/4" compared to over 3/8" for the original and the hose ID is 3/8 compared to 7/16+

Flow/volume must be pretty resticted compared to the original design?
Last edit: 05 Jun 2011 17:11 by luc.

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Z1 oil cooler

05 Jun 2011 17:37
#455634
Probably depends on the model of bike, the smaller 4's use a high pressure oil system with plain bearing cranks were as the bigger 4's Z1's,Kz900,Kz1000 & Kz1100 have a low pressure(2.3-2.8 PSI) oil system due to roller bearing cranks.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • luc
  • luc's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 78
  • Thanks: 1

Re: Z1 oil cooler

05 Jun 2011 17:41
#455636
I was talking apecifically about the Z.

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Z1 oil cooler

05 Jun 2011 18:04
#455641
As to why the differences in hose fitting diameters, I can only guess...

On my 1982 GPz 1100 B2 model, I about fell over when pricing a new set of oil cooler hoses, so being creative, I got out my dremel tool with a cutoff wheel and sliced in half the crimp or swage holding the return and supply hose to the fittings.

The inner diameter of the hose is very close to 3/8"(0.375). Having a race supplier close when I lived in San Diego Ca. (Earl's Supply), I purchased a nice long length of low pressure, oil resistant rubber hose. After cutting the hose's to fit and using fuel injection hose clamps for the fit to the Kawasaki oil cooler fittings, I've had no problems.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • Jeff.Saunders
  • Jeff.Saunders's Avatar
  • Offline
  • Vendor
  • Vendor
    Vendors
  • Posts: 1238
  • Thanks: 149

Re: Z1 oil cooler

05 Jun 2011 19:20
#455652
1/4" ID is plenty of opening.

On my turbocharged Z1, I run a restrictor in the oilway that is 1/8" ID. This is to boost the oil pressure going to the turbo. The engine runs happily using the 1/8" restrictor.

Please Log in or Create an account to join the conversation.

  • racer54
  • racer54's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1902
  • Thanks: 114

Re: Z1 oil cooler

05 Jun 2011 19:38
#455655
Exactly where did you put the restrictor. Used to to able to buy a spring that went in the oil housing under the carbs.
1980 LTD (changed over the years), 1979 LTD (being rebuilt), 1977 KZ turbo and various KZ's in various states of build. KLX110

Please Log in or Create an account to join the conversation.

  • Jeff.Saunders
  • Jeff.Saunders's Avatar
  • Offline
  • Vendor
  • Vendor
    Vendors
  • Posts: 1238
  • Thanks: 149

Re: Z1 oil cooler

05 Jun 2011 20:30
#455660
It's a Mr Turbo part - it screws into the oil pipe housing where the oil pressure switch usually goes. Because I removed the oil pressure switch, I run a low poundage (0-15lb oil pressure switch on the oil gallery just behind the RH side of the cylinder block.

Please Log in or Create an account to join the conversation.

  • racer54
  • racer54's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1902
  • Thanks: 114

Re: Z1 oil cooler

05 Jun 2011 20:49
#455664
Thanks Jeff...good to know!
1980 LTD (changed over the years), 1979 LTD (being rebuilt), 1977 KZ turbo and various KZ's in various states of build. KLX110

Please Log in or Create an account to join the conversation.

  • luc
  • luc's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 78
  • Thanks: 1

Re: Z1 oil cooler

05 Jun 2011 20:58
#455667
Jeff.Saunders wrote: It's a Mr Turbo part - it screws into the oil pipe housing where the oil pressure switch usually goes. Because I removed the oil pressure switch, I run a low poundage (0-15lb oil pressure switch on the oil gallery just behind the RH side of the cylinder block.

Do you mean an oil pressure GAUGE instead of switch?
I also have an 0-15 mechanical gauge there but the only smalll and low scale gauge that i could find are really designed for fuel pressure on carburated cars and are not that precise on the low end.( 1 or 2 psi)
What are you using?
Good to know that I'm not starving my engine with 1/4" NPT/ -6 fittings and 3/8 lines.
Still I wish that the after-market would have kept the same sizes that were engineered by the factory

Please Log in or Create an account to join the conversation.

  • Jeff.Saunders
  • Jeff.Saunders's Avatar
  • Offline
  • Vendor
  • Vendor
    Vendors
  • Posts: 1238
  • Thanks: 149

Re: Z1 oil cooler

06 Jun 2011 12:01
#455768
I do run a fairly old pressure gauge. When cold I get readings around 10-12 psi, this drops to 2-3 psi when the engine is warm. As long as I have oil pressure, that's really all I care about. These Z1 engines run on such low oil pressure, it's not usually a concern.

Back in the days when I drag raced (late 1970's), the oil light would often flicker during the runs. After 200+ 1/4 mile passes I never had any issues. When I sold the bike in 1980, the bike had 50,000 miles on it and most of those were very hard miles.

Please Log in or Create an account to join the conversation.

  • hocbj23
  • hocbj23's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: Z1 oil cooler

06 Jun 2011 15:29
#455781
Only ways to "starve" one of these engines is to run it with too little oil,or hammer on it to the point that the oil pump pickup runs dry.U can cure that potential problem by putting a simple Schnitz oil gate in the crankcase.Keeps the oil from running rearward on hard acceleration.Have one in my bike and it does the trick.bj

Please Log in or Create an account to join the conversation.

  • Jeff.Saunders
  • Jeff.Saunders's Avatar
  • Offline
  • Vendor
  • Vendor
    Vendors
  • Posts: 1238
  • Thanks: 149

Re: Z1 oil cooler

06 Jun 2011 17:37 - 06 Jun 2011 17:39
#455802
hocbj23 wrote: Only ways to "starve" one of these engines is to run it with too little oil,or hammer on it to the point that the oil pump pickup runs dry.U can cure that potential problem by putting a simple Schnitz oil gate in the crankcase.Keeps the oil from running rearward on hard acceleration.Have one in my bike and it does the trick.bj

These do help. I ran a similar setup for several years in one of the bikes I drag raced and rode hard on the street.

With my turbo bike, I have a modified oil pump and pan with a deep extension at the rear and the oil pickup moved to the bottom of the extension.





BTW, the oil pan/pump was modified by Frank Davis at Powerhouse Motorcycles.
www.fastcycles.com/
Last edit: 06 Jun 2011 17:39 by Jeff.Saunders.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum