Valve noise-checked clearances
- Brown_Muscle
-
Topic Author
- Offline
- User
-

Registered
- Posts: 49
- Thanks: 0
Valve noise-checked clearances
09 Jun 2011 18:40 - 09 Jun 2011 18:53
Hey All, The bike is a 79 KZ1000ST, I got it with 944 miles on it it now has 1014. I checked the valve clearances because of excessive valve train noise. They were all within spec.
The problem is, from what i can hear, a single valve/cam lobe is making a very loud clicking/ticking noise, where-as the others are pretty quiet. From what i can hear i am almost certain it is the exhaust valve on cylinder number 3 (although don't take my word on it, its just sounds pretty definitive). Another symptom is the exhaust pipe is turning purple towards the head, as though its running lean-which it most likely is, i still have to sync the carbs with vacuum gauges. However i was unsure if the two were related. Any advice or help is greatly appreciated! Thanks
-Phil
Edit* I should have mentioned the bike runs great, idles smooth, and has smooth acceleration, however i have not had it over 5K RPM as of yet.
The problem is, from what i can hear, a single valve/cam lobe is making a very loud clicking/ticking noise, where-as the others are pretty quiet. From what i can hear i am almost certain it is the exhaust valve on cylinder number 3 (although don't take my word on it, its just sounds pretty definitive). Another symptom is the exhaust pipe is turning purple towards the head, as though its running lean-which it most likely is, i still have to sync the carbs with vacuum gauges. However i was unsure if the two were related. Any advice or help is greatly appreciated! Thanks
-Phil
Edit* I should have mentioned the bike runs great, idles smooth, and has smooth acceleration, however i have not had it over 5K RPM as of yet.
1979 KZ1000ST
Last edit: 09 Jun 2011 18:53 by Brown_Muscle.
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: Valve noise-checked clearances
09 Jun 2011 18:59
With that low mileage, clearly the bike sat for extended periods. If that pipe was shiney chrome and in less than 100 miles is turning dark something is way out of whack! Are you sure you're not hearing detonation? I would check the carbs, ignition, and spark plugs to make sure everything is as should be. I don't believe you'll find the problem is related to carb synch as that pretty much only affects idle. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- Brown_Muscle
-
Topic Author
- Offline
- User
-

Registered
- Posts: 49
- Thanks: 0
Re: Valve noise-checked clearances
09 Jun 2011 19:19
I'm pretty sure it's not detonation, however i could be wrong, I can post a video of the noise at a later time if that is helpful. The plugs all have a nice tan coloration to them. The noise generally exists from idle to 2000RPM or so, then it gets quiet. Carbs are rebuilt and were bench synced and tuned. I can check the ignition and make sure everything's good.
1979 KZ1000ST
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: Valve noise-checked clearances
09 Jun 2011 19:23
One pipe, or all the pipes turning purple?
If it is just on pipe, then you have an air leak of some kind, the float level is way too low for some reason, or the mixture screws have not been tuned properly.
Tune those mixture screws. Find the stumble spots for each carburetor and compare them to eachother. - Post results.
If it is just on pipe, then you have an air leak of some kind, the float level is way too low for some reason, or the mixture screws have not been tuned properly.
Tune those mixture screws. Find the stumble spots for each carburetor and compare them to eachother. - Post results.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- Brown_Muscle
-
Topic Author
- Offline
- User
-

Registered
- Posts: 49
- Thanks: 0
Re: Valve noise-checked clearances
09 Jun 2011 19:36 - 09 Jun 2011 20:00
Just one pipe- cyl# 3, It's possible the float level is incorrect, or the air screw is incorrect. The carbs only have one adjustment screw on it- the air screw, as the service manual calls it. I turned them in all the way and backed them out 1 and 1/8 turns, as the manual says.
I'm semi-new to tuning carbs, how would i go about finding the stumble spots exactly??
Thanks guys!!
*edit* Also the exhaust pipe on that side has a hole the size of a dime in it...I'm unsure if that would throw anything off enough to matter?
I'm semi-new to tuning carbs, how would i go about finding the stumble spots exactly??
Thanks guys!!
*edit* Also the exhaust pipe on that side has a hole the size of a dime in it...I'm unsure if that would throw anything off enough to matter?
1979 KZ1000ST
Last edit: 09 Jun 2011 20:00 by Brown_Muscle.
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: Valve noise-checked clearances
09 Jun 2011 20:15Brown_Muscle wrote: Just one pipe- cyl# 3, It's possible the float level is incorrect, or the air screw is incorrect. The carbs only have one adjustment screw on it- the air screw, as the service manual calls it. I turned them in all the way and backed them out 1 and 1/8 turns, as the manual says.
I'm semi-new to tuning carbs, how would i go about finding the stumble spots exactly??
Thanks guys!!
*edit* Also the exhaust pipe on that side has a hole the size of a dime in it...I'm unsure if that would throw anything off enough to matter?
OH BOY. Yes the gigantic hole in the exhaust probly has alot to do with it.
Isnt it like super shit balls loud?!?! :laugh: How cloase to the head is the hole?
Take that to a welding shop and have them seal it with a bung or plug or somethin before you go messing with anything else.
Finding the stumble spots would be turning the air screw in till the engine stumbles, then counting the turns, screw it out till it stumbles. Basically finding too rich and too lean. They should all stumble near the same positions if everything is ok.
Good luck!
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- Brown_Muscle
-
Topic Author
- Offline
- User
-

Registered
- Posts: 49
- Thanks: 0
Re: Valve noise-checked clearances
09 Jun 2011 20:23
Ahh i should have specified, its around where the crossover pipe is for the two mufflers- so it would probably be effecting both cylinders on that side. The muffler/pipe is already patched with flashing and JB weld (LOL) as a temporary fix. (that hole is the size of, oh, a soda can!) The small hole was patched as well but blew off.... I need a new pipe for that side to say the least.
I'll try to plug the hole, do the stumble test, and report back!
I'll try to plug the hole, do the stumble test, and report back!
1979 KZ1000ST
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: Valve noise-checked clearances
09 Jun 2011 20:26Brown_Muscle wrote: Ahh i should have specified, its around where the crossover pipe is for the two mufflers- so it would probably be effecting both cylinders on that side. The muffler/pipe is already patched with flashing and JB weld (LOL) as a temporary fix. (that hole is the size of, oh, a soda can!) The small hole was patched as well but blew off.... I need a new pipe for that side to say the least.
I'll try to plug the hole, do the stumble test, and report back!
Right on
Good luck.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Valve noise-checked clearances
09 Jun 2011 21:52Brown_Muscle wrote: ...79 KZ1000ST, I got it with 944 miles on it it now has 1014. I checked the valve clearances because of excessive valve train noise. They were all within spec.
The problem is, from what i can hear, a single valve/cam lobe is making a very loud clicking/ticking noise, where-as the others are pretty quiet. From what i can hear i am almost certain it is the exhaust valve on cylinder number 3...exhaust pipe is turning purple towards the head, as though its running lean-which it most likely is, i still have to sync the carbs with vacuum gauges. However i was unsure if the two were related....
Might be exhaust gasket leak on #3.
Would assure exhaust clamp nuts are snug on #3.
Could test by removing #3 plug wire while engine is running to see whether the noise changes.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Valve noise-checked clearances
09 Jun 2011 22:01
Am thinking 79 KZ1000ST has side located pilot air adjustment screws that turn in clockwise to enrichen by reducing air and turn out counter-clockwise to lean by allowing more air.
On "lean running" #3, could try turning the pilot air screw 1/2 turn in clockwise to enrichen the pilot mixture.
Good Fortune!
On "lean running" #3, could try turning the pilot air screw 1/2 turn in clockwise to enrichen the pilot mixture.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Brown_Muscle
-
Topic Author
- Offline
- User
-

Registered
- Posts: 49
- Thanks: 0
Re: Valve noise-checked clearances
10 Jun 2011 12:34 - 10 Jun 2011 12:35
Some awesome ideas here- I tried all of them
-Unplugging the spark plug did not change the noise, except slow it down since the idle slowed.
-I loosened and retightened all the exhaust flange nuts, no change in noise
For the stumble test, I did one at a time, and all of them had almost no stumble when turned all the way in, the engine ran ever so slightly rougher, however only when they were bottomed out. As far as turning them outwards, they were all about 2.5 turns, except for cylinder number 4, which was about 1 3/4 or 2 turns outwards.
After i set them all back to 1 and 1/8 turn i turned cyl #3 half a turn inwards, as far as i could tell it made no difference, and readily revved to 6K rpm with no issues, however hopefully it wont be running as hot.
any more ideas? I'd love to ride it some more but i don't want to do any damage to the engine.
-Unplugging the spark plug did not change the noise, except slow it down since the idle slowed.
-I loosened and retightened all the exhaust flange nuts, no change in noise
For the stumble test, I did one at a time, and all of them had almost no stumble when turned all the way in, the engine ran ever so slightly rougher, however only when they were bottomed out. As far as turning them outwards, they were all about 2.5 turns, except for cylinder number 4, which was about 1 3/4 or 2 turns outwards.
After i set them all back to 1 and 1/8 turn i turned cyl #3 half a turn inwards, as far as i could tell it made no difference, and readily revved to 6K rpm with no issues, however hopefully it wont be running as hot.
any more ideas? I'd love to ride it some more but i don't want to do any damage to the engine.
1979 KZ1000ST
Last edit: 10 Jun 2011 12:35 by Brown_Muscle.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Valve noise-checked clearances
10 Jun 2011 15:13 - 10 Jun 2011 15:13Brown_Muscle wrote: ...set them all back to 1 and 1/8 turn i turned cyl #3 half a turn inwards, as far as i could tell it made no difference....
When turning the pilot air adjustment screw fails to cause a noticeable change in rpm, that's evidence of something being wrong in the carb pilot circuit, often an imperfectly clean pilot circuit.
Wear Eye Protection !
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 10 Jun 2011 15:13 by Patton.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
