Igniton coil

  • wgrothman
  • wgrothman's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 17
  • Thanks: 0

Igniton coil

11 Jun 2011 19:17
#456704
How can I tell if my ignition coil is bad. My wiring is prob screwed anyway so I'll prob have to get a new harness. Is there a way to test only the ignition coil

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Igniton coil

11 Jun 2011 19:38
#456710
What model & year of bike? Twin or 4 cylinder?

I wrote this for the bigger 4's, but it applies for the smaller ones too:

Ignition Coil Primary And Secondary Wiring

Ignition coils on the 80’s Kz1000,Kz1100’s and Gpz1100’s are wired the same, that is as you sit on the bike, the LEFT ignition coil primary(small wires) are two wires, RED and BLACK. The secondary (or sparkplug wires) go to #1 and #4 sparkplugs(your primary wiring may be different).

The cylinders are numbered left to right as you sit on the seat; #1,#2,#3, and #4.

For the RIGHT ignition coil, the primary wires, again are two wires, RED and GREEN, with the secondary going to #2 and #3.

The RED wire gets it’s voltage from the run/stop switch on the right handlebar switch pod.

The BLACK and GREEN wires connect to the IC Igniter(if the bike has the Kawasaki supplied electronic ignition) it actually gives the coils their grounds to fire the sparkplugs.

Primary(small wires) side of the coils will read between 1.8 to 3.0 ohms.

Secondary(sparkplug wire ports)side of the coil will read between 10.4K to 15.6K ohms. These ports are wired together, so it makes no difference which is used, as long as the correct coil to sparkplug configuration is followed.

The sparkplug caps should read 5K OHMS, any higher, or a reading of infinity means new caps should be ordered.

To stress the ignition coils, take a hair dryer, heat the coils and see if the ohm readings change from cold to hot . If they do, it’s time to buy new coils.
Keep in mind, the wiring is reversed for the 550’s 650‘s and 750‘s, that is the RIGHT coil primary will be two wires, RED and BLACK with the secondary(sparkplugs) going to #1 and #4.

The LEFT coils primary wiring would be again two wires, RED and GREEN, with the secondary(sparkplugs) going to #2 and #3.

These engines have what is known as a “Wasted Spark” that is, a sparkplug will fire during an exhaust stroke. It does no damage and many other motorcycle engines have this design.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • wgrothman
  • wgrothman's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 17
  • Thanks: 0

Re: Igniton coil

11 Jun 2011 23:30
#456753
It's a 1978 kz750b twin. It's also missing the ignition. Would you happen to know how to wire it to start

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Igniton coil

11 Jun 2011 23:48
#456757
wgrothman wrote: It's a 1978 kz750b twin. It's also missing the ignition. Would you happen to know how to wire it to start

A basic requirement is having battery positive voltage furnished to the coil primary terminal. Which may be done with a hot wire from the positive battery post (or any voltage source).

Remember to disconnect the hot wire after no longer attempting to start the engine. Because constant voltage supplied to a "resting" ignition coil may at some point fry the coil.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum