1000 Upper End - Cam Chain Question

  • supercharged
  • supercharged's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 390
  • Thanks: 7

1000 Upper End - Cam Chain Question

13 Jun 2011 01:16
#456936
I could use some help. 20,000 mile 1978 KZ1000 LTD
starts and runs great
has reasonably load noise from head maybe a loud tick somewhat center
rules out exhaust leak and carbs
pulled cam cover and found:
- 1 - cam chain and idler look OK
- Turned crank and observed that upper end appears to working well (see note 2)
- Checked cam chain for tension throughout the crank cycle and found one piece of chain that when between the intake and exhaust cam, there is slack... only in this one spot.

I guess this signifies the need to replace the cam chain? Any input?

- 2 - While looking at the cams, the upper end was filled with oil. As I turned the engine, the oil from the cam wells was drained. This is normal. BUT the #4 exhaust valve well is still filled with oil. Why would this not be draining? Is this an issue that needs resolving?

Thanks
Mike D
- 79 KZ1000 LTD Supercharged
- 80 KZ1000 1105cc Pridmore/Vetter tribute
- 79 Honda CBX
- 03 Z1000 Mod
- 80 KZ1000 LTD Modified
- 80 KZ1000 LTD PROJECT on Hold
- 78 KZ1000/900 - Street big block
- 78 KZ1000-NEEDS HELP!
- 80 CBX -Project STARTED
- 81 GPZ1100
- GSRX1200
- 80 CB750F supersport... eahhh not so good
- 80 CB750F supersport
- 1988 KZ1000 Police - 50K miles
- 1978 KZ1000 LTD - should be a quick project
- 2001 KZ1000 Police - 30K miles - chromed Sgt Bike GREAT SHAPE

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: 1000 Upper End - Cam Chain Question

13 Jun 2011 07:22
#456960
20k miles is very early to need a cam chain. If you have a Kawasaki factory service manual take a look to see if it describes how to measure the cam chain for wear. My KZ650 manual describes this procedure, and it's really easy to do, I assume the KZ1000 has a similar method. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • roy-b-boy-b
  • roy-b-boy-b's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 3245
  • Thanks: 103

Re: 1000 Upper End - Cam Chain Question

13 Jun 2011 08:50
#456964
I worked on a bike that had slack when you rotated the engine,like you in one spot.

Someone had let the bike sit outside and the engine filled with water and the bottom timing sprocket rusted on the bottom. This is on the crank sprocket.

I hope this is not the case with your bike. Roy
1979 LTD Street Fighter.1977 KZ1000

Please Log in or Create an account to join the conversation.

  • supercharged
  • supercharged's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 390
  • Thanks: 7

Re: 1000 Upper End - Cam Chain Question

18 Jun 2011 23:44
#458110
just to let you know - i did a cam chain adjustment and all is fine. Heard the adjuster click as I released it taking up some slack. Now no noise from the upper end.

I think a return port is clogged that caused the load of oil to remain, but I did not remove the cams. Valve clearance was good... so I put it back together for now.
Mike D
- 79 KZ1000 LTD Supercharged
- 80 KZ1000 1105cc Pridmore/Vetter tribute
- 79 Honda CBX
- 03 Z1000 Mod
- 80 KZ1000 LTD Modified
- 80 KZ1000 LTD PROJECT on Hold
- 78 KZ1000/900 - Street big block
- 78 KZ1000-NEEDS HELP!
- 80 CBX -Project STARTED
- 81 GPZ1100
- GSRX1200
- 80 CB750F supersport... eahhh not so good
- 80 CB750F supersport
- 1988 KZ1000 Police - 50K miles
- 1978 KZ1000 LTD - should be a quick project
- 2001 KZ1000 Police - 30K miles - chromed Sgt Bike GREAT SHAPE

Please Log in or Create an account to join the conversation.

  • cavanaughracing
  • cavanaughracing's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 213
  • Thanks: 25

Re: 1000 Upper End - Cam Chain Question

19 Jun 2011 21:36 - 19 Jun 2011 21:39
#458239
supercharged wrote: just to let you know - i did a cam chain adjustment and all is fine. Heard the adjuster click as I released it taking up some slack. Now no noise from the upper end.

I think a return port is clogged that caused the load of oil to remain, but I did not remove the cams. Valve clearance was good... so I put it back together for now.

Very doubtful that's the case. Oil has to run down past the bucket to get to the return galley. It's possible you have a little varnish build up on the tappets.

78's were known for top idlers wearing out. It can be worn pretty good and be masked by chain tension. The only real good way to tell is by removing it and inspecting it for slop.

Another problem area is the shoe in front of the block. I've seen a lot of broken ones.
Last edit: 19 Jun 2011 21:39 by cavanaughracing.

Please Log in or Create an account to join the conversation.

  • supercharged
  • supercharged's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 390
  • Thanks: 7

Re: 1000 Upper End - Cam Chain Question

19 Jun 2011 22:29
#458247
Larry - thank for the heads up. I will investigate further. I may do a 1075 on this engine, so that will allow me the inspection.

BTW, have you ever replaced a cam chain without removing the crank? If I do the 1075, I thought of replacing chain as well, but haven't even looked to see f they sell the rivet masters.
Mike D
- 79 KZ1000 LTD Supercharged
- 80 KZ1000 1105cc Pridmore/Vetter tribute
- 79 Honda CBX
- 03 Z1000 Mod
- 80 KZ1000 LTD Modified
- 80 KZ1000 LTD PROJECT on Hold
- 78 KZ1000/900 - Street big block
- 78 KZ1000-NEEDS HELP!
- 80 CBX -Project STARTED
- 81 GPZ1100
- GSRX1200
- 80 CB750F supersport... eahhh not so good
- 80 CB750F supersport
- 1988 KZ1000 Police - 50K miles
- 1978 KZ1000 LTD - should be a quick project
- 2001 KZ1000 Police - 30K miles - chromed Sgt Bike GREAT SHAPE

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Please Log in or Create an account to join the conversation.

  • cavanaughracing
  • cavanaughracing's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 213
  • Thanks: 25

Re: 1000 Upper End - Cam Chain Question

20 Jun 2011 21:21
#458415
supercharged wrote: Larry - thank for the heads up. I will investigate further. I may do a 1075 on this engine, so that will allow me the inspection.

BTW, have you ever replaced a cam chain without removing the crank? If I do the 1075, I thought of replacing chain as well, but haven't even looked to see f they sell the rivet masters.

Oh yea..... I've installed master link cam chains in KZ's before. I dont' like to but they work. Yamaha did them that way back in the late 70's ..early 80's.

I haven't reused any of the cam chain idlers in years. I toss that stuff and put Liska components in them.

Please Log in or Create an account to join the conversation.

  • cavanaughracing
  • cavanaughracing's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 213
  • Thanks: 25

Re: 1000 Upper End - Cam Chain Question

20 Jun 2011 21:21 - 20 Jun 2011 21:24
#458417

Do you work on commission :laugh:

The tool costs more than the chain :woohoo:
Last edit: 20 Jun 2011 21:24 by cavanaughracing.

Please Log in or Create an account to join the conversation.

  • hocbj23
  • hocbj23's Avatar
  • User
  • User
    Public
  • Thanks: 0

Re: 1000 Upper End - Cam Chain Question

20 Jun 2011 21:24
#458419
Oh-oh. Mr BS-34 is back Hi,Larry,where u been?bj

Please Log in or Create an account to join the conversation.

  • cavanaughracing
  • cavanaughracing's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 213
  • Thanks: 25

Re: 1000 Upper End - Cam Chain Question

20 Jun 2011 21:29
#458422
hocbj23 wrote: Oh-oh. Mr BS-34 is back Hi,Larry,where u been?bj

Hi BJ :) How's that CSR working? You haven't been drag racing again this summer...have you?

Please Log in or Create an account to join the conversation.

  • ELCouz
  • ELCouz's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 376
  • Thanks: 5

Re: 1000 Upper End - Cam Chain Question

26 Jun 2011 16:21 - 26 Jun 2011 16:21
#459491
Can you join/break (with rivet tool) a hyvo type cam chain or you need to split the cases?

regards,
laurent
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe
Last edit: 26 Jun 2011 16:21 by ELCouz.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum