Problem with starting on kz750e

  • zed810
  • zed810's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 40
  • Thanks: 0

Problem with starting on kz750e

14 Jun 2011 18:29
#457279
First of all let me say hi to everyone!
i live in scotland and run a modded kz750e specs are;

wiseco 810 bore kit
web cams
ported head with orient express valve springs
used to run mikuni rs34s but those were sold and now runs bs34s 140 main 40 slow running jets
vance and hines pro stock pipe ( i think)

the problem i have is the starter clutch was slipping so i replaced the rollers, springs,pins AND the starter gear it runs on but it still slips a bit when trying to start the compression is high so think this might be the cause (180psi)
this was no problem with the rs34s as all i needed to do was two pumps of the accel pumps to squirt fuel in and it would fire right up, but with the bs34s i have to give a squirt through the carbs with some fuel and it fires immediately, but if i don't i wont start, choke system is working ok and once it has had it's first start in the morning it will start all day no probs does'nt even turn over a full revolution and it bangs into life.
i know it is basically a race spec motor and some concessions have to be made and it is seriously quick lifting the front wheel under acceleration in third and revs in excess of the rev counter so i would like to know what any of you think at the moment a use a little nitro car filling bottle that lives under the seat and if it's sat a while give it a little squirt in each carb. ideally i would like another set of rs34s, but money is tight at the moment it went much quicker with them on.
1981 z750e1 gpz 750a1 tank and side panels 810 bore kit web cams mikuni bs34 vance and hines pipe

Please Log in or Create an account to join the conversation.

  • MFolks
  • MFolks's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6650
  • Thanks: 541

Re: Problem with starting on kz750e

14 Jun 2011 19:10
#457284
What weight and grade of oil used? If car oil, the friction modifiers in it are not compatable with wet plate clutches in these bikes. Also the car oil may make the starter clutch slip.

Good spark at the plugs? Float bowls set properly? Clean air filter? No dirty fuel filter?
Checked input voltage at the primary(small wires) side of the coils? It should be almost the same as battery voltage.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)

Please Log in or Create an account to join the conversation.

  • zed810
  • zed810's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 40
  • Thanks: 0

Re: Problem with starting on kz750e

15 Jun 2011 05:12
#457366
hi, thanks for reply, the oil i use is 10/40 fully synth motorcycle oil, i think you misunderstand i mean the starter clutch slips float heights are ok, voltage checks out good
1981 z750e1 gpz 750a1 tank and side panels 810 bore kit web cams mikuni bs34 vance and hines pipe

Please Log in or Create an account to join the conversation.

  • zed810
  • zed810's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 40
  • Thanks: 0

Re: Problem with starting on kz750e

15 Jun 2011 05:14
#457368
will maybe try mineral oil for next change and see if it helps
1981 z750e1 gpz 750a1 tank and side panels 810 bore kit web cams mikuni bs34 vance and hines pipe

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum