any suggestions? tips on reassembly?
- bigkzfan
-
Topic Author
- Offline
- User
-

Registered
- if grandpa had tits he"d be grandma, if
- Posts: 156
- Thanks: 1
any suggestions? tips on reassembly?
14 Jun 2011 21:49
hello everyone can anyone offer any suggestion on a pain less reinstall of the top end of a kz1000 j engine?? like how to avoid oil leaks like i had the first time at the base gasket...tips on getting cams back in and in time?? i just want this to be the last time i have to do this again..my first attempt was a total failure..but i am gonna spend this friday and saturday doing it again..thank you guys so much for your help along the way...i would be lost without everyones help on here!!!!
hello, i own a 1982 kz1000 j model with a 4into1 header and factory air box...
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: any suggestions? tips on reassembly?
15 Jun 2011 11:36
go slowly and make sure and double check that everything is right the first time.
clean gasket surfaces,watch for any high spots.using a blade(only the blade) for a drywall knife is a good way to clean and check gasket surfaces.hold it straight up and down so that you can scrape the gasket off and any high spots will be revealed because this method rely's on the straight edge of the blade to reveal and level any highs spots.as long as everything is square and level new gaskets should seal it back up just fine.take your time setting the timing up and double check it until you are satisfied it is right.
what specifically are you sweating about the rebuild?
leon
clean gasket surfaces,watch for any high spots.using a blade(only the blade) for a drywall knife is a good way to clean and check gasket surfaces.hold it straight up and down so that you can scrape the gasket off and any high spots will be revealed because this method rely's on the straight edge of the blade to reveal and level any highs spots.as long as everything is square and level new gaskets should seal it back up just fine.take your time setting the timing up and double check it until you are satisfied it is right.
what specifically are you sweating about the rebuild?
leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Please Log in or Create an account to join the conversation.
- bigkzfan
-
Topic Author
- Offline
- User
-

Registered
- if grandpa had tits he"d be grandma, if
- Posts: 156
- Thanks: 1
Re: any suggestions? tips on reassembly?
15 Jun 2011 13:53
oil leaks and the big one is getting cams back in and in time...these engines are a pain in the backside lol
hello, i own a 1982 kz1000 j model with a 4into1 header and factory air box...
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: any suggestions? tips on reassembly?
15 Jun 2011 17:08 - 15 Jun 2011 17:13
Get a factory manual if you don't have one. Get new O ring seals for all the oil feed tubes and seal points between the crankcase and cylinder.
I would use 3-bond on the cylinder base gasket. Mine came with it from the factory that way.
Be careful with cam timing as you can ding a valve and bend it if they are off.
I would use 3-bond on the cylinder base gasket. Mine came with it from the factory that way.
Be careful with cam timing as you can ding a valve and bend it if they are off.
1979 KZ-750 Twin
Last edit: 15 Jun 2011 17:13 by bountyhunter.
Please Log in or Create an account to join the conversation.
- bigkzfan
-
Topic Author
- Offline
- User
-

Registered
- if grandpa had tits he"d be grandma, if
- Posts: 156
- Thanks: 1
Re: any suggestions? tips on reassembly?
15 Jun 2011 17:23
man that 3 bond is a pain to work with lol what about copper coat on both sides of the base gasket??
hello, i own a 1982 kz1000 j model with a 4into1 header and factory air box...
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: any suggestions? tips on reassembly?
15 Jun 2011 18:13
copper coat should be fine.
take your time and go by the book for the timing.
leon
take your time and go by the book for the timing.
leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: any suggestions? tips on reassembly?
15 Jun 2011 19:39
copper coat is da bomb!
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- bigkzfan
-
Topic Author
- Offline
- User
-

Registered
- if grandpa had tits he"d be grandma, if
- Posts: 156
- Thanks: 1
Re: any suggestions? tips on reassembly?
15 Jun 2011 20:38
shew i just do not wanna fool with that yamabond ever again lol... that stuff is so freakin messy lol
hello, i own a 1982 kz1000 j model with a 4into1 header and factory air box...
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
