Timing Chain Slack
- rcarver
-
Topic Author
- Offline
- User
-

Registered
- Posts: 62
- Thanks: 0
Timing Chain Slack
15 Jun 2011 23:47
1979 KZ650 SR:
I did a valve adjustment over the weekend and the bike ran and sounded great right after the adjustment. But the next day it started to tap again noticeably around cylinder #4, which was the one cylinder that was way out in comparison to the rest.
Tonight I pulled the valve cover to re-check the clearances. Right when I pulled the cover off I noticed the timing chain had a lot of slack. I took the bolt out of the automatic tensioner and turned the crankshaft and everything tightened right back up.
Is this normal? Or possibly a sign of a bad tensioner and maybe why I was getting tapping sound again?
I did recheck the clearances but the motor was still warm (running out of daylight) so I don't think my measurements where accurate, going to check tomorrow on a cold motor.
I did a valve adjustment over the weekend and the bike ran and sounded great right after the adjustment. But the next day it started to tap again noticeably around cylinder #4, which was the one cylinder that was way out in comparison to the rest.
Tonight I pulled the valve cover to re-check the clearances. Right when I pulled the cover off I noticed the timing chain had a lot of slack. I took the bolt out of the automatic tensioner and turned the crankshaft and everything tightened right back up.
Is this normal? Or possibly a sign of a bad tensioner and maybe why I was getting tapping sound again?
I did recheck the clearances but the motor was still warm (running out of daylight) so I don't think my measurements where accurate, going to check tomorrow on a cold motor.
1979 KZ650 SR (aka: Stella Blue)
Please Log in or Create an account to join the conversation.
- ELCouz
-
- Offline
- User
-

Registered
- Posts: 376
- Thanks: 5
Re: Timing Chain Slack
26 Jun 2011 16:36
What's your mileage ?
You could have attained the maximum slack the tensionner can take ... by cam chain wear or tensionner guide wear or cam sprockets wear!
Also check your carb sync it could make it slap like hell !!!
regards,
laurent
You could have attained the maximum slack the tensionner can take ... by cam chain wear or tensionner guide wear or cam sprockets wear!
Also check your carb sync it could make it slap like hell !!!
regards,
laurent
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe
Please Log in or Create an account to join the conversation.
- hocbj23
-
- User
-

Public
- Thanks: 0
Re: Timing Chain Slack
26 Jun 2011 16:43
Not sure about the 650 but on the 1000 the manual specifies a procedure for resetting the auto tensioner.On the 1000,u need to take the tensioner out,retract the tensioner guide,tighten the bolt in the fully retracted position,reinstall the tensioner,them put #1 at TDC,loosen the tensioner bolt until it takes up the slack and then retighten the bolt.Maybe the 650 is different.bj
Please Log in or Create an account to join the conversation.
- ELCouz
-
- Offline
- User
-

Registered
- Posts: 376
- Thanks: 5
Re: Timing Chain Slack
26 Jun 2011 16:50 - 26 Jun 2011 16:53Not sure about the 650 but on the 1000 the manual specifies a procedure for resetting the auto tensioner.On the 1000,u need to take the tensioner out,retract the tensioner guide,tighten the bolt in the fully retracted position,reinstall the tensioner,them put #1 at TDC,loosen the tensioner bolt until it takes up the slack and then retighten the bolt.Maybe the 650 is different.bj
Depending the type of tensioner he have (mostly cross-wedge type in late models) he only need to remove the big bolt cap , the spring and the part that slide this will automatically reset the tensioner (by pushing the guide inside the head)...
Just be careful not to remove the other little bolt since it could cause the tentioner to fall into the engine!
EDIT: either way it will work, its just that my tensioner thread are weak
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe
Last edit: 26 Jun 2011 16:53 by ELCouz.
Please Log in or Create an account to join the conversation.
- rcarver
-
Topic Author
- Offline
- User
-

Registered
- Posts: 62
- Thanks: 0
Re: Timing Chain Slack
27 Jun 2011 09:40 - 27 Jun 2011 09:44
Thanks guys...the bike is a 1979 KZ650-SR with approx. 31,000miles.
I went ahead and installed an APE Timing Chain Tensioner. I got it installed per the instructions (and a few recommendations on KZrider). The bike fired right up and the chain chatter really quieted down a lot.
A few things though:
1) After about an hour of riding a little chain chatter came back. I assume it is because everything warmed up and stretched out a bit. I was going to tighten the APE tensioner up a little to take out the slack. Is it a bad idea to tighten the tensioner further to take up the slack of a warm chain/engine?
2) I was also hoping that installing the new tensioner would bring my cam timing marks closer to the correct alignment spec with the top of the cylinder head...but no matter how I adjusted the cams the marks are always off by about 1/8".
I went ahead and installed an APE Timing Chain Tensioner. I got it installed per the instructions (and a few recommendations on KZrider). The bike fired right up and the chain chatter really quieted down a lot.
A few things though:
1) After about an hour of riding a little chain chatter came back. I assume it is because everything warmed up and stretched out a bit. I was going to tighten the APE tensioner up a little to take out the slack. Is it a bad idea to tighten the tensioner further to take up the slack of a warm chain/engine?
2) I was also hoping that installing the new tensioner would bring my cam timing marks closer to the correct alignment spec with the top of the cylinder head...but no matter how I adjusted the cams the marks are always off by about 1/8".
1979 KZ650 SR (aka: Stella Blue)
Last edit: 27 Jun 2011 09:44 by rcarver.
Please Log in or Create an account to join the conversation.
- hocbj23
-
- User
-

Public
- Thanks: 0
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
