trust a helicoil?
- Mandyrew
-
Topic Author
- Offline
- User
-

Registered
- Posts: 26
- Thanks: 0
trust a helicoil?
17 Jun 2011 12:40
Well, I'm two weeks into motorcycle ownership for the first time in my life, and I wanted a bike I could afford that needed some tinkering so I could learn about bikes ... and I sure got one!
The latest complete newbie mistake is that I got a generic torque wrench from True Value that had non-exact adjustments... well, I stripped my engine drain bolt. "well, time for a new oil pan" thought I ... but on these bikes the plug hole is part of the whole engine block ...
So, does everybody trust a helicoil on a bolt that, if falls out, spills out 3L of oil on your back tire and everybody else?
And after that I get to take off my wheel and put in new brake shoes ... good times!
The latest complete newbie mistake is that I got a generic torque wrench from True Value that had non-exact adjustments... well, I stripped my engine drain bolt. "well, time for a new oil pan" thought I ... but on these bikes the plug hole is part of the whole engine block ...
So, does everybody trust a helicoil on a bolt that, if falls out, spills out 3L of oil on your back tire and everybody else?
And after that I get to take off my wheel and put in new brake shoes ... good times!
KZ440 LTD '81
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: trust a helicoil?
17 Jun 2011 13:50
Ah, the joy of cheap tools. You may want to see if you can get a Timesert in the size you need. I have no personal experience with it, but from what I've read that is a more robust repair. Or it may be possible to bore the hole a little larger and tap it to the next larger size bolt. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- RonKZ650
-
- Offline
- User
-

Registered
- Posts: 3719
- Thanks: 252
Re: trust a helicoil?
17 Jun 2011 13:50
If it's possible to helicoil it, that will be fine for repair. A helicoil will never fall out.
321,000 miles on KZ's that I can remember. Not going to see any more.
Please Log in or Create an account to join the conversation.
- Mandyrew
-
Topic Author
- Offline
- User
-

Registered
- Posts: 26
- Thanks: 0
Re: trust a helicoil?
17 Jun 2011 14:09 - 17 Jun 2011 14:15
thanks guys. So drain the oil, put the bike on its side, drill it, tap it, helicoil insert, and new bolt/gasket.
Anything I'm missing?
Also, any advise for making sure I catch all the shards that are created by drilling/tapping? Not sure what kind of grease could be best on the drill, and whether I should flush with my regular oil after the service...
Anything I'm missing?
Also, any advise for making sure I catch all the shards that are created by drilling/tapping? Not sure what kind of grease could be best on the drill, and whether I should flush with my regular oil after the service...
KZ440 LTD '81
Last edit: 17 Jun 2011 14:15 by Mandyrew. Reason: added detail
Please Log in or Create an account to join the conversation.
- mtkawboy
-
- Offline
- User
-

Registered
- Posts: 822
- Thanks: 16
Re: trust a helicoil?
17 Jun 2011 16:23 - 17 Jun 2011 16:25
Wheel bearing grease, go slow, back it out , clean and regrease it often. I wouldnt even worry about the oil if you do it like I said. Ive done tham that way on car intake manifolds. If youre worried put an extra quart in and let it run thru & drain out, put the drain plug in and fill it. Id trust a helicoil more then the original factory threaded hole
78-KZ1000/1105, 80 KZ1000, 82 Kawasaki GPZ750, 95 Harley Fatboy, 80 Suzuki GS1100ET, 81 GS1100E parts bike, 83 GS1100SD Katana/1394,78 Yamaha XT500, 81 Yamaha XS650, 78 Yamaha XS650E, 48 Whizzer model J motorbike, 71 Honda CT70H, 71 Honda CT70, 81 IT 250 Yamaha,82 Honda XL100S owned
Last edit: 17 Jun 2011 16:25 by mtkawboy.
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: trust a helicoil?
17 Jun 2011 17:26
that would be a fairly large bolt hole. maybe a spark plug thread repair kit would be the right size? some plugs are 14mm. similar to heli coil but it is a threaded insert.
i have used them with success .u dont need to drill, just tap. i put grease on the tap and just cut a tiny bit then retracted the tap, remove the shaving that was stuck to the grease and repete.
i have used them with success .u dont need to drill, just tap. i put grease on the tap and just cut a tiny bit then retracted the tap, remove the shaving that was stuck to the grease and repete.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- testarossa
-
- Offline
- User
-

Registered
- Attack life, it's only trying to kill you.
- Posts: 3673
- Thanks: 83
Re: trust a helicoil?
17 Jun 2011 19:11
Does anyone know off the top of their head what size thread is on the drain plug? It is possible that you could find an oversize drain plug at the parts store. It seems to me that I have seen over size plugs to 18mm or so. Just as the counter guy in your favorite parts house before you go tapping anthing. If they stock a +1 drain plug in your size, then you just screw it in and go.
1978 KZ1000 A2 Click--->Build Thread
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN
2004 ZX-10R
2007 Harley Sportster 1200
2020 Harley Street Glide Special
Angola, IN
Please Log in or Create an account to join the conversation.
- KZ250LTD
-
- Offline
- User
-

Registered
- Posts: 1311
- Thanks: 16
Last edit: 13 Feb 2012 18:23 by KZ250LTD.
Please Log in or Create an account to join the conversation.
- JR
-
- Offline
- Sustaining Member
-

Registered
- Posts: 2981
- Thanks: 501
Re: trust a helicoil?
17 Jun 2011 21:50testarossa wrote: Does anyone know off the top of their head what size thread is on the drain plug? It is possible that you could find an oversize drain plug at the parts store. It seems to me that I have seen over size plugs to 18mm or so. Just as the counter guy in your favorite parts house before you go tapping anthing. If they stock a +1 drain plug in your size, then you just screw it in and go.
Exactly !
My local Canadian tire store has a wide selection of oversize drain plugs made for this very purpose. Dont matter that they are labelled "Auto".
1980 kz750E1, Delkevic exhaust
Please Log in or Create an account to join the conversation.
- Mandyrew
-
Topic Author
- Offline
- User
-

Registered
- Posts: 26
- Thanks: 0
Re: trust a helicoil?
18 Jun 2011 00:47
Well, from bad to worse. General consensus from my mechanic and all was to tap it with a 14 mm 1.25 thread and put in a new bolt ... the tap just completely flattened the threads in there and created nothing. i greased it and went easy and slow but now there's just smooth aluminum up there, and ain't nothing screwing in. I think i just gotta take it in and they'll probably go up yet another size. Pretty frustrating for such an uncomplicated problem.
So all you beginning tinkerers out there: never, ever buy a cheap torque wrench.
As far as the tap goes, all i can surmise is that when they're brand new, they're super sharp and you just can't go slow and easy enough. i just don't know how this got so messed up.
Oi.
So all you beginning tinkerers out there: never, ever buy a cheap torque wrench.
As far as the tap goes, all i can surmise is that when they're brand new, they're super sharp and you just can't go slow and easy enough. i just don't know how this got so messed up.
Oi.
KZ440 LTD '81
Please Log in or Create an account to join the conversation.
- Mandyrew
-
Topic Author
- Offline
- User
-

Registered
- Posts: 26
- Thanks: 0
Re: trust a helicoil?
18 Jun 2011 00:48
My factory drain plug was 10mm, with 1.25 threads
KZ440 LTD '81
Please Log in or Create an account to join the conversation.
- Mandyrew
-
Topic Author
- Offline
- User
-

Registered
- Posts: 26
- Thanks: 0
Re: trust a helicoil?
18 Jun 2011 00:50
...so find a shop near you that uses them and bring them your oil pan...
On this model, the pan is built into the engine block.
On this model, the pan is built into the engine block.
KZ440 LTD '81
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
