Sprocket + chain change= groove

  • wizardmc
  • wizardmc's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 16
  • Thanks: 0

Sprocket + chain change= groove

18 Jun 2011 14:06
#458024
Here's the problem changed front sprocket (one tooth smaller) and went to o-ring chain.
Behind chain at at front sprocket is now a nice groove in the enginge case caused by chain rivets.
I didn't hot-rod around on this bike and the groove is only a few thou deep should I worry much, and
is there a inexpensive fix. Will space the sprocket out a little but will that mess up chain alaignment causeing faster wear on both sprockets. Should mention this happened quite a while ago
(8 years) just before I bought a new bike and never noticed it. Finally getting it back on the road and don't want a broken case. Bike is a '77 KZ1000. Any suggestions or pointing me to an expert
is appreciated.
77 KZ1000A1
TTU,Texas

Please Log in or Create an account to join the conversation.

  • seanbarney41
  • seanbarney41's Avatar
  • Offline
  • User
  • User
    Registered
  • '79 kz1000 LTD '75 Honda CB750
  • Posts: 438
  • Thanks: 23

Re: Sprocket + chain change= groove

18 Jun 2011 15:00
#458031
pretty sure slightly offset sprockets(get the same offset for both front and rear) will be an easy bolt on solution...should be available for your bike but not sure where...maybe call Z1 Enterprises(knowledgeable folks on the phone!)If I'm wrong, I bet a know it all is about to correct me...

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Sprocket + chain change= groove

18 Jun 2011 16:12
#458046
Something may be either mis-aligned or not assembled properly. The 1977 KZ650 bikes originally came with O-ring chains. I don't know for sure, but it seems likely that the KZ1000 would also have come with that type, so the chain should not interfere with the case. Maybe someone with knowledge of an original '77 KZ1000 can verify the original chain type. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • MDawnz1
  • MDawnz1's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 319
  • Thanks: 27

Re: Sprocket + chain change= groove

18 Jun 2011 22:51
#458096
Is it the chain on the bike NOW that caused the grove?
If not then forget it.
Cheaper chains have to be made out of thicker metal.
If you are going to space your sprockets, you HAVE to do both or you will mess up everything.
1974 Z1a, still 903

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Sprocket + chain change= groove

18 Jun 2011 23:00 - 18 Jun 2011 23:01
#458098
Perhaps c/s sprocket was installed without spacer washers when spacer washers were needed.
Some replacement sprockets come with a shoulder on the engine side which eliminates need for spacer washers.
www.z1enterprises.com/detail.aspx?ID=226

Clearance in this area between chain and case may be verified after installation by hand-rotating the rear wheel with transmission in gear to turn the sprocket and listen for any scrapping noise.

Good Fortune! :)
1973 Z1
KZ900 LTD
Last edit: 18 Jun 2011 23:01 by Patton.

Please Log in or Create an account to join the conversation.

  • Old Man Rock
  • Old Man Rock's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 6071
  • Thanks: 225

Re: Sprocket + chain change= groove

18 Jun 2011 23:44 - 18 Jun 2011 23:46
#458109
As mentioned, thin washer spacer behind the front sprocket you should be ok...

Only a few thousands....
Compared to this your golden.... :pinch: :whistle: :laugh:

File her smooth around the edges :pinch: , cleaned out the shavings/metal dust, new tabbed lock washer, lube the chain and have been riding her for almost 2 years since. ;)

1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter

Phoenix, Az
Last edit: 18 Jun 2011 23:46 by Old Man Rock.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum