another z750 starter clutch thread
- zed810
-
Topic Author
- Offline
- User
-

Registered
- Posts: 40
- Thanks: 0
another z750 starter clutch thread
20 Jun 2011 18:58
my starter clutch has always been a bit iffy so i decided to strip it, found broken springs and the staeter gear was worn so replaced rollers, pins, springs and starter gear that the clutch runs on and put back together.
verdict?
absolutely no difference get about one revolution before it slips!!!!!
the only part i did not change was the unit that holds the rollers etc as appeared ok with no cracks?
meant to mention the bike has a 10.25-1 wiseco 810 conversion and web 450' lift cams any ideas would be greatly appreciated!
thanks
gordon
verdict?
absolutely no difference get about one revolution before it slips!!!!!
the only part i did not change was the unit that holds the rollers etc as appeared ok with no cracks?
meant to mention the bike has a 10.25-1 wiseco 810 conversion and web 450' lift cams any ideas would be greatly appreciated!
thanks
gordon
1981 z750e1 gpz 750a1 tank and side panels 810 bore kit web cams mikuni bs34 vance and hines pipe
Please Log in or Create an account to join the conversation.
- The Milkman
-
- Offline
- User
-

Registered
- Posts: 794
- Thanks: 194
Re: another z750 starter clutch thread
20 Jun 2011 21:38
A weak starter will do the same thing. What happens is a cylinder will fire and jump the motor faster, if the starter motor can't keep up with it, it kicks the starter clutch out. If you have ever had a bendix go in a car starter wear out it does the same thing. Older Ford starters were noted for having a weak bendix. Pull the starter and check the end bushing that is on the outside of the engine. They get dry and cause a drag on the starter so it won't keep up with the engine when it fires. I usually just put some never seize on the shaft if the bushing isn't ovaled.
Good luck,
Les
Good luck,
Les
78 650-C2, Stock engine, Jardine 4-2 Exh., 17-38 sprockets, dyna ignition and coils, coil wiring mod, carb mod.
The following user(s) said Thank You: GPz550D1
Please Log in or Create an account to join the conversation.
- zed810
-
Topic Author
- Offline
- User
-

Registered
- Posts: 40
- Thanks: 0
Re: another z750 starter clutch thread
21 Jun 2011 18:24
thanks, pulled starter checked brushes were good gave them and commutator a clean and lubed the end bush still no luck.
1981 z750e1 gpz 750a1 tank and side panels 810 bore kit web cams mikuni bs34 vance and hines pipe
Please Log in or Create an account to join the conversation.
- The Milkman
-
- Offline
- User
-

Registered
- Posts: 794
- Thanks: 194
Re: another z750 starter clutch thread
21 Jun 2011 22:38
Is your battery fully charged and all the cables and connections clean, tight and making good contact?
Les
Les
78 650-C2, Stock engine, Jardine 4-2 Exh., 17-38 sprockets, dyna ignition and coils, coil wiring mod, carb mod.
The following user(s) said Thank You: GPz550D1
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: another z750 starter clutch thread
21 Jun 2011 23:15
You don't have your year and model in your signature. but the starter has a 1 way clutch/ sprag. Here is a picture from the net, look at the one on the right. You will see if the Inner or outer pieces that the rollers fit into are worn enough, then the Locking function cannot occur and it will slip. If you put in new rollers and springs and it still slips then these mating parts are also worn.
Probably available from Z1 for your bike.
Probably available from Z1 for your bike.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- zed810
-
Topic Author
- Offline
- User
-

Registered
- Posts: 40
- Thanks: 0
Re: another z750 starter clutch thread
22 Jun 2011 06:06
thanks its a 1981 z750e model i had come to that conclusion but after buying the rollers and spring and inner race i was hoping it was'nt! pretty much comfirmed it so time to throw more money at it! will keep youse posted
1981 z750e1 gpz 750a1 tank and side panels 810 bore kit web cams mikuni bs34 vance and hines pipe
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: another z750 starter clutch thread
22 Jun 2011 09:17
Look as though there is a updated part for the outer starter clutch assy.
#13194 13193-1062 ! CLUTCH-ASSY-ONEWAY
Then the gear may also be worn.
#12046 12046-1032 SPROCKET,STARTER,58T
#13194 13193-1062 ! CLUTCH-ASSY-ONEWAY
Then the gear may also be worn.
#12046 12046-1032 SPROCKET,STARTER,58T
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: another z750 starter clutch thread
22 Jun 2011 10:44 - 22 Jun 2011 10:45zed810 wrote: thanks its a 1981 z750e model i had come to that conclusion but after buying the rollers and spring and inner race i was hoping it was'nt! pretty much comfirmed it so time to throw more money at it! will keep youse posted
It's easy to put the information about bike year and model in your signature where it will automatically appear in posted messages, and likely elicit better responses.
When done, the signature information appears in all posts, past and future.
And may be changed as often as desired.
Attachment addsig.jpg not found
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 22 Jun 2011 10:45 by Patton.
The following user(s) said Thank You: GPz550D1
Please Log in or Create an account to join the conversation.
- zed810
-
Topic Author
- Offline
- User
-

Registered
- Posts: 40
- Thanks: 0
Re: another z750 starter clutch thread
22 Jun 2011 16:23
thanks that exploded view is not of a 1981 z750 four cylinder there is an idler gear that is not present on my bike.
thanks
thanks
1981 z750e1 gpz 750a1 tank and side panels 810 bore kit web cams mikuni bs34 vance and hines pipe
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: another z750 starter clutch thread
22 Jun 2011 16:53 - 22 Jun 2011 16:55
Sorry, that is the drawing that comes up for the 81-750 E2. Maybe there is a mistake in the parts system. Or maybe you are missing this idler? Do you have the Factory Manual for your bike? Does it show this clearly for no idler?
www.cyclepartsnation.com/pages/OemParts#...50-E2-1981/080120D-3
www.cyclepartsnation.com/pages/OemParts#...50-E2-1981/080120D-3
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 22 Jun 2011 16:55 by Motor Head.
The following user(s) said Thank You: GPz550D1
Please Log in or Create an account to join the conversation.
- zed810
-
Topic Author
- Offline
- User
-

Registered
- Posts: 40
- Thanks: 0
Re: another z750 starter clutch thread
23 Jun 2011 05:48
strange.... don't remember seeing the idler in there i thought the starter gear acted directly on the starter motor gear...... but i do see that the two thrust washers are'nt there (i had been apart previously) another strip down then!
1981 z750e1 gpz 750a1 tank and side panels 810 bore kit web cams mikuni bs34 vance and hines pipe
Please Log in or Create an account to join the conversation.
- zed810
-
Topic Author
- Offline
- User
-

Registered
- Posts: 40
- Thanks: 0
Re: another z750 starter clutch thread
23 Jun 2011 05:49
not by me i must add!
1981 z750e1 gpz 750a1 tank and side panels 810 bore kit web cams mikuni bs34 vance and hines pipe
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
