CAMSHAFT TIMING
- kwak650
-
Topic Author
- Offline
- User
-

Registered
- Posts: 20
- Thanks: 0
CAMSHAFT TIMING
23 Jun 2011 17:13
I am trying to set the timing chain on my 1981 1000csr(J style engine). With the crank on the T mark for
1&4 cylinders, I can't get the arrow aligned with the EX mark on the exhaust camshaft to be exactly flush with the cylinder head as shown in my manual. It is either a little down or if I move it 1 tooth it goes up a little past it. The actual picture in the manual shows it a little up but the illustration shows the arrow exactly flush. I need some advise I don't want to do it wrong. Thanks:
1&4 cylinders, I can't get the arrow aligned with the EX mark on the exhaust camshaft to be exactly flush with the cylinder head as shown in my manual. It is either a little down or if I move it 1 tooth it goes up a little past it. The actual picture in the manual shows it a little up but the illustration shows the arrow exactly flush. I need some advise I don't want to do it wrong. Thanks:
Please Log in or Create an account to join the conversation.
- jonnybravo
-
- Offline
- Banned
-

Registered
- Posts: 518
- Thanks: 18
Re: CAMSHAFT TIMING
23 Jun 2011 17:32
when u tighten the cam caps that will bring it down, if it dont loosen and adjust
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: CAMSHAFT TIMING
23 Jun 2011 17:34
Have you measured the cam chain for stretch? There is a procedure in the manual, so many links, so much distance. Might be stretched, or maybe the front guide is worn. Are you checking it with the camshaft tightened? With the tensioner out, put your finger in the hole and apply pressure to the rear guide to take up the slack. There is also a straight line and a notch on the end of the camshaft itself. this should parallel the gasket surface.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- kwak650
-
Topic Author
- Offline
- User
-

Registered
- Posts: 20
- Thanks: 0
Re: CAMSHAFT TIMING
23 Jun 2011 18:08
I have the cam caps installed also the tensioner installed. i have checked for stretch and it is within spec.Should the arrow be exactly flush with the head?
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: CAMSHAFT TIMING
23 Jun 2011 18:14
You may know this already, but Don't put the valve cover back on with the tensioner in.
So cams are in, tightened, but you can't tell the correct tooth for the EX? Well from the bikes I've done I go off of the line and notches on the end of the cams, as well as looking at the line/ mark on the gear. Holding a straight edge along them may help. No counting from the crank up to the EX cam mark unfortunately.
So cams are in, tightened, but you can't tell the correct tooth for the EX? Well from the bikes I've done I go off of the line and notches on the end of the cams, as well as looking at the line/ mark on the gear. Holding a straight edge along them may help. No counting from the crank up to the EX cam mark unfortunately.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- kwak650
-
Topic Author
- Offline
- User
-

Registered
- Posts: 20
- Thanks: 0
Re: CAMSHAFT TIMING
23 Jun 2011 18:18
Thanks, I've tried everything to get them lined up so I'll give it a try with a straight edge tonight.
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: CAMSHAFT TIMING
23 Jun 2011 18:21
The only other way would be with a degree wheel and dial indicator. Then you could be 100% accurate with your cam timing. But unless you have a stretched out chain or worn guides you should get it within a couple of degrees following the factory marks.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- bigkzfan
-
- Offline
- User
-

Registered
- if grandpa had tits he"d be grandma, if
- Posts: 156
- Thanks: 1
Re: CAMSHAFT TIMING
23 Jun 2011 23:07
yes the arrows must line up with the parting lines like the manual...i just went thru this headache last saturday... line the front exhaust arrow with the front parting line hold that chain tight when feeding both cams in then with the first pin above the front parting line count 44 pins to the rear and align that with your intake arrow..it will seem to be about one or maybe 2 pins above rear parting line then install cam caps tighten down in sequence like the manual says except for 12ft lbs of torque keep in mind you will probably have to push down on cam caps to get cams to seat before drawing down the cam cap bolts..i did this with a big pair of channel locks in one hand while starting the bolts with the other once i got the cam bolts tightened down the marks lined up perfect. then i put valve cover on with 4 bolts holding it down in the middle to engage top cam chain guide adjusted manual cam chain adjuster and rolled engine over by hand 2 times back to top dead center pulled valve cover back off re-counted the pins and it was still exactly 44 pins like the manual says with both arrows lined up like they should be..hope this helps..i just thank everyone on here for sharing the knowledge and know how to help me on my way with this same problem
hello, i own a 1982 kz1000 j model with a 4into1 header and factory air box...
Please Log in or Create an account to join the conversation.
- bigkzfan
-
- Offline
- User
-

Registered
- if grandpa had tits he"d be grandma, if
- Posts: 156
- Thanks: 1
Re: CAMSHAFT TIMING
23 Jun 2011 23:14 - 24 Jun 2011 10:20
one thing i also did is once i got the engine set to top dead center i loosely put a pair of vice grips on that 17mm nut rested them on the case gaurd to hold it on tdc while doing the cam shaft install this was a big help holding crank at tdc
hello, i own a 1982 kz1000 j model with a 4into1 header and factory air box...
Last edit: 24 Jun 2011 10:20 by bigkzfan. Reason: correction
Please Log in or Create an account to join the conversation.
- kwak650
-
Topic Author
- Offline
- User
-

Registered
- Posts: 20
- Thanks: 0
Re: CAMSHAFT TIMING
26 Jun 2011 16:16
Well after a few more times I got it very close. I am thinking that the chain must be stretched even though it was suppose to have been checked by someone who says they know what they are doing. Anyway turned over a few times by hand, there was no binding so I fired it up. Everything seems good, never had it out for a road test yet. Thanks for all the good input.
Please Log in or Create an account to join the conversation.
- ELCouz
-
- Offline
- User
-

Registered
- Posts: 376
- Thanks: 5
Re: CAMSHAFT TIMING
26 Jun 2011 16:22
Nice keep us updated on this 
Have a nice ride!
laurent
Have a nice ride!
laurent
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe
Please Log in or Create an account to join the conversation.
- bigkzfan
-
- Offline
- User
-

Registered
- if grandpa had tits he"d be grandma, if
- Posts: 156
- Thanks: 1
Re: CAMSHAFT TIMING
27 Jun 2011 13:50
its probably not a stretched chain...trust me i went thru this hell
hello, i own a 1982 kz1000 j model with a 4into1 header and factory air box...
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
