Cam end cap leak

  • bloglos
  • bloglos's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 229
  • Thanks: 0

Cam end cap leak

24 Jun 2011 13:50
#459139
Ordered up a new set of 4 cam end caps for my project bike as it leaked like crazy when I fired it up. Manual says to use some sort of gasket sealer on the caps to prevent leaking.

What do you folks use? There seems to be a large selection available. Any tips or tricks?
78 KZ650 C2 - Runner
77 KZ650 B1 - Project

Please Log in or Create an account to join the conversation.

  • johnbgood
  • johnbgood's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 45
  • Thanks: 4

Re: Cam end cap leak

24 Jun 2011 13:54
#459141
Hi

I used Yamabond.

Regards

Johnbgood
KZ1000P 1991

Please Log in or Create an account to join the conversation.

  • bigkzfan
  • bigkzfan's Avatar
  • Offline
  • User
  • User
    Registered
  • if grandpa had tits he"d be grandma, if
  • Posts: 156
  • Thanks: 1

Re: Cam end cap leak

24 Jun 2011 14:17
#459146
use the right stuff its great..yamabond is soooooo messy just saying :) just my 2cents
hello, i own a 1982 kz1000 j model with a 4into1 header and factory air box...

Please Log in or Create an account to join the conversation.

  • RonKZ650
  • RonKZ650's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 3719
  • Thanks: 252

Re: Cam end cap leak

24 Jun 2011 14:19
#459147
Yamabond #4 to be exact. Give it a chance though unless it's really leaking badly. It seems they often leak at first start, then seal fine after that.
321,000 miles on KZ's that I can remember. Not going to see any more.

Please Log in or Create an account to join the conversation.

  • bloglos
  • bloglos's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 229
  • Thanks: 0

Re: Cam end cap leak

24 Jun 2011 17:33
#459177
It's leaking quite badly and I really should have known better then to try and reuse the old ones, they were practically falling apart when I took them out, but I was too excited to fire it up. I'll try either The Right Stuff or the Yamabond as they are readily available. Now I only have to wait for our Canada Post strike to be over to get my parts :(
78 KZ650 C2 - Runner
77 KZ650 B1 - Project

Please Log in or Create an account to join the conversation.

  • toad
  • toad's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 196
  • Thanks: 7

Re: Cam end cap leak

24 Jun 2011 17:33
#459178
I let the bonding agent set up a little while before tightening to spec.
78 kz 1000
wiesco 1015
29mm smoothbores
gs1100 swingarm
gsxr rear

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Cam end cap leak

24 Jun 2011 18:23
#459183
I used permatex ultra black HI-temp bonding sealer and it has worked very well. The secret is in the application. Clean the head pockets with acetone, apply a bead of sealer to them and wipe to a film with your finger. Apply a bead to the curved sides of the plug and spread to a thin film. Set plugs into the head and then:

Place valve cover on (no gasket now) and insert cover bolts.

GENTLY pull down cover bolts (use a socket in your fingers) just enough to pull the tops of the end plugs down almost even with the top surface of the head. Wipe off excess sealer. Let dry overnight and carefully remove cover. The end plugs should be bonded into place correctly.

You can install cover/gasket now. I run a thin bead of sealer across the top of the end plugs and about an inch either side of them as they sometimes seep oil at the corners.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • bloglos
  • bloglos's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 229
  • Thanks: 0

Re: Cam end cap leak

24 Jun 2011 18:34
#459184
Good stuff. This might be a stupid question, but I'm still learning. What exactly is the purpose of these caps, other then to leak?
78 KZ650 C2 - Runner
77 KZ650 B1 - Project

Please Log in or Create an account to join the conversation.

  • RonKZ650
  • RonKZ650's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 3719
  • Thanks: 252

Re: Cam end cap leak

24 Jun 2011 18:46
#459186
bloglos wrote: Good stuff. This might be a stupid question, but I'm still learning. What exactly is the purpose of these caps, other then to leak?

When they machine the camshaft recesses in the head they machine all the way across the top of the head so you need to plug these up and came up with these wonderful cam end plugs. Once you remove them, throw them away, they will always leak. My experience at least. Other guys make it work.
321,000 miles on KZ's that I can remember. Not going to see any more.

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Cam end cap leak

25 Jun 2011 03:20
#459250
They have to line bore through from the side to get the holes perfectly aligned that mount the camshafts. That leaves the holes on the end that have to be plugged. If they had any mercy they would supply aluminum "half circles" machined to fit that we could glue in with sealer and they would last the life of the engine.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • ELCouz
  • ELCouz's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 376
  • Thanks: 5

Re: Cam end cap leak

26 Jun 2011 14:58 - 26 Jun 2011 14:59
#459468
If they had any mercy they would supply aluminum "half circles" machined to fit that we could glue in with sealer and they would last the life of the engine.

In fact you can get them from a third party... cost more but no leaks with proper gasket maker...

I think APE and IIRC z1enterprises sell them too!

regards,
laurent
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe
Last edit: 26 Jun 2011 14:59 by ELCouz.

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Cam end cap leak

26 Jun 2011 15:18
#459475
ELCouz wrote:
If they had any mercy they would supply aluminum "half circles" machined to fit that we could glue in with sealer and they would last the life of the engine.

In fact you can get them from a third party... cost more but no leaks with proper gasket maker...

I think APE and IIRC z1enterprises sell them too!

regards,
laurent
Available for some engines, but not mine (750 twin).
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum