cam chain tensioner working?

  • indianajames
  • indianajames's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 93
  • Thanks: 1

cam chain tensioner working?

27 Jun 2011 18:07
#459752
took cam cover off to fix leaky end plugs and cam chain was pretty slack but normal . i read some where here that it would tighten on its own and i wouldn't be able to reinstall cam chain cover without damage to engine . but mine went right back on without any resistance from chain slider inside cam chain cover . now im freekin out about starting it. i have noticed a chain slap noise at low rpms but it almost completely went away after carb sync. what should i do , i haven't rotated engine wiith cam cover off . this 1982 750 ltd has 19497miles i don't wanna kill it because of a gasket replacement !!!

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: cam chain tensioner working?

27 Jun 2011 19:06
#459777
indianajames wrote: took cam cover off to fix leaky end plugs and cam chain was pretty slack but normal . i read some where here that it would tighten on its own and i wouldn't be able to reinstall cam chain cover without damage to engine . but mine went right back on without any resistance from chain slider inside cam chain cover . now im freekin out about starting it. i have noticed a chain slap noise at low rpms but it almost completely went away after carb sync. what should i do , i haven't rotated engine wiith cam cover off . this 1982 750 ltd has 19497miles i don't wanna kill it because of a gasket replacement !!!

Am thinking the cautionary advice refers to KZ550.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • indianajames
  • indianajames's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 93
  • Thanks: 1

Re: cam chain tensioner working?

27 Jun 2011 19:40
#459792
thanx patton, no worries then?

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: cam chain tensioner working?

27 Jun 2011 20:31
#459804
I thought the caution applied to KZ550, but am having doubts as to which models the caution applies, and found the following posts:
loudhvx wrote: If that motor uses a Hy-vo camchain, don't even re-installl the valve cover without relasing the camchain tension. That will lead to valve train damage. I think 81's would have had hy-vo, but not sure....
Motor Head wrote: Putting the valve cover on, with the tensioner still in, is a bad Idea. This is with the 80 or something and newer with the Silent multi plate link Hi-vo chain, with the upper chain guide in the valve cover. Damage to a guide can result....

I believe the 1982 KZ750LTD does have a Hy-vo cam chain.
But it sounds like your valve cover fit back on without meeting any resistance from the cam chain.

Don't suspect an issue in this case, but will try to determine what the FSM provides, and meanwhile await better advice from other members.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: cam chain tensioner working?

27 Jun 2011 20:40 - 27 Jun 2011 20:42
#459806
I would assume you have the early style tensioner 12048, that requires loosening the bolt for the spring to come forward. That is the upper one in the picture. The later style 12048A, lower in picture, has the cross wedge and will move forward when valve cover is removed. Then taking the cap with the 17mm size wrench off, the spring out and the wedge. This will allow the main spring to retract as the valve cover is reinstalled.

1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 27 Jun 2011 20:42 by Motor Head.
The following user(s) said Thank You: indianajames

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: cam chain tensioner working?

27 Jun 2011 21:11
#459820


Seems to me that the main idea is to not allow the tensioner to over-extend against a loosened cam chain which would over-tighten the chain during reassembly, whether by tightening the cam caps or replacing the valve cover on some particular models.

My recollection about the KZ550 is that the valve cover itself plays a part in keeping the chain taught, and that replacing the cover serves to tighten the chain, which likely over-tightens a chain that has already had slack removed by operation of the tensioner. Regardless of the type of chain, whether Hy-vo or bicycle style.

Perhaps Lou, of loudhvx fame, may again venture forth to shed additional light on the subject.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • indianajames
  • indianajames's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 93
  • Thanks: 1

Re: cam chain tensioner working?

27 Jun 2011 23:21
#459851
thanx fellas, motorhead ,i have the tensioner with the cap bolt.which is why i was concerned that there wasn't any resistance from chain cover ,no automatic deslakifacation. but i didn't rotate engine maybe i got lucky or tensioner is not working which would explain chain slap noise at low rpms . patton, that's not in my clymar ,surprize! maybe the PO locked it to replace gasket or something . maybe i should release lock bolt , rotate tire in gear and listen for it to click into place ? or remove cap bolt and check the spring mechanism ? thanx patton, and motorhead im realy worried , i love this bike!

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: cam chain tensioner working?

28 Jun 2011 00:12
#459867
Here's a link to a good site that includes an excellent free down-loadable service manual:
kz.mbsween.com/

After opening the site,


Good Fortune! :)
1973 Z1
KZ900 LTD
The following user(s) said Thank You: indianajames

Please Log in or Create an account to join the conversation.

  • indianajames
  • indianajames's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 93
  • Thanks: 1

Re: cam chain tensioner working?

28 Jun 2011 11:01
#459943
thanx patton, but i cant access this type of file as i am useing my brothers playstation to have internet . i guess i will just pull the tensioner and see what happens . i just thought someone here would know what to do

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: cam chain tensioner working?

28 Jun 2011 11:24
#459944
Motor Head wrote: I would assume you have the early style tensioner 12048, that requires loosening the bolt for the spring to come forward. That is the upper one in the picture. The later style 12048A, lower in picture, has the cross wedge and will move forward when valve cover is removed. Then taking the cap with the 17mm size wrench off, the spring out and the wedge. This will allow the main spring to retract as the valve cover is reinstalled.


Presupposing, as does motorhead, that
you have the early style tensioner 12048, that requires loosening the bolt for the spring to come forward. That is the upper one in the picture,

and that all you did was
took cam cover off to fix leaky end plugs and cam chain was pretty slack but normal...reinstall cam chain cover...mine went right back on without any resistance from chain slider inside cam chain cover

and that you did not loosen the bolt,

I believe the tensioner remained in the same position before, during and after removal and replacement of the cam cover, whereby the tension adjustment remained the same as it existed before the cam cover was removed.

In other words, the tensioner was already locked in its existing position, where it stayed because it wasn't unlocked.

Would be a different result and different procedure with the later model tensioner the later style 12048A, lower in picture, has the cross wedge and will move forward when valve cover is removed.

I don't think you need to bother with pulling the tensioner to see what happens.

Good Fortune! :)
1973 Z1
KZ900 LTD
The following user(s) said Thank You: indianajames

Please Log in or Create an account to join the conversation.

  • loudhvx
  • loudhvx's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 10863
  • Thanks: 1622

Re: cam chain tensioner working?

28 Jun 2011 12:46
#459961
750-4 and 550 use similar tensioners. They both adjust tension continually.

Only the 750 has the small retainer bolt, but that is only to stop the tension shaft from falling into the engine. It does not affect operations in normal use.

Tensioner mechanisms should never be installed with the cross-wedge and cap installed on the tensioner body. This can snap a chain.

The valve cover, as you guys know, should not be removed and installed without loosening the tension. Usually you would just remove the cap and cross wedge to release tension. This is for both the 750 and 550.

(You really should never touch that small bolt on the 750 tensioner. It's only for when you are rebuilding the tensioner itself.)

Now, if you remove the valve cover, there is a small chance that the cams will be in a position where they will not want to rotate on their own. If you remove the valve cover, and nothing turns at all, then you should be able to re-install the valve cover without any problem, even without loosening the cap and cross wedge.

The problem is, there is no way of knowing whether the cams moved or not when you remove the cover. Any movement will happen while the colver is just barely lifted, so you won't be able to see under it. That's why the warning is for any time you remove the cover.

Indianajames: all you need to do to be safe, at this point, is remove the cap (16 or 17mm hex) and cross wedge, then slowly rotate engine forward slightly, then re-install cross-wedge and cap. The cahin will be loose for second after that, but it should tighten back up automatically. It will also tighten up more, gradually, after the engine warms up.

This is assuming the tensioner is working properly.
The following user(s) said Thank You: Patton, indianajames

Please Log in or Create an account to join the conversation.

  • indianajames
  • indianajames's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 93
  • Thanks: 1

Re: cam chain tensioner working?

28 Jun 2011 15:59
#459991
thanx patton, and loudhvx i have the tensioner in lower picture ,thats why i was concerned that there wasn't any resistance . i think i got lucky cams didn't rotate .gonna remove hex cap and wedge and rotate as per your excellent advice . i feel 100% confident now . KZRIDER KICKS AZZ!!!!!!!!!!!!!!!!!!!!!!!!!!!

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum