clutch cable
- kz1000newbee
-
Topic Author
- Offline
- User
-

Registered
- Posts: 4
- Thanks: 0
clutch cable
30 Jun 2011 00:15
ok. so I've goten my hands real dirty and done a lot to my bike, learning my trail. Everything was a great learning experience and the bike is really shaping up. Things were good until I took the cover off the clutch area for 3 hours of buffing it to a nice shine (21 years of grim does not polish easily. That's when the trouble started. Long story short I'm pretty sure how it all works but I just cannot get the cluch cable to work the way it should.
Should the intermediate adjustment "nuts" be connected to either side of the cable? It seems to me that they should be but both ends are loose from the cable so no matter what I do to them I cannot seem to get the cable to work properly. My bike is a 1990 kz1000p. It is a fairly new cable that a mechanic put on a few months ago and was working fine until I took the cover off and the release-comp-clutch part came off. I do understand that with the cable in it should point towards the back of the bike and that it rides on the ball bearings and the lifter plate pushes in the clutch rod........ Just confused as all hell as to what is going on. HELP, thanks
Should the intermediate adjustment "nuts" be connected to either side of the cable? It seems to me that they should be but both ends are loose from the cable so no matter what I do to them I cannot seem to get the cable to work properly. My bike is a 1990 kz1000p. It is a fairly new cable that a mechanic put on a few months ago and was working fine until I took the cover off and the release-comp-clutch part came off. I do understand that with the cable in it should point towards the back of the bike and that it rides on the ball bearings and the lifter plate pushes in the clutch rod........ Just confused as all hell as to what is going on. HELP, thanks
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: clutch cable
30 Jun 2011 02:33
See if this helps:
Clutch Cable Replacement On Some Kawasaki Motorcycles
With Proper Mechanism Adjustments
1.About mid way down the clutch cable is an adjuster; shorten the cable as much as possible.
2.Remove the small cover on the left side of the sprocket cover and loosen up the lock nut on the clutch throw out mechanism.
3.Remove the shifter lever; the sprocket cover, and lay the cover on some rags or news papers.
4.Have on hand a small cotter pin that will be needed to prevent the new clutch cable from coming out of the throw out mechanism.
5.At the left handlebar turn in the slack adjusters for the clutch cable and then take out the pivot bolt.
6.New clutch cables may or may not have lubrication; now's the time to either hang the new cable up overnight so heavy oil can flow through it or buy a cable luber kit with the special clamp and can of spray lube.
7.Attach the cable to the cover's throw out mechanism and secure it with a new cotter pin.
8. While you're in there, check the wiring from the alternator(YELLOW WIRES, or any wires from the alternator), remove the excess chain lube from the clutch push rod and check the wire routing that goes above the engine sprocket.
9. Check the lock washer for cracks on the engine sprocket and any "Hooking" of the sprocket teeth.
10 Route the clutch cable the same way the old one was and connect the cable to the clutch lever; and the pivot bolt gets re-installed.
11.Carefully install the sprocket cover, making sure the push rod is engaged and then tighten up the cover.
12.Adjusting the clutch play and cable tension is real easy; using a flat bladed screwdriver, turn the slotted screw clockwise(to the right) until it becomes hard to turn; then turn it counterclockwise(to the left) 1/4 turn and tighten the lock nut.
13.The mid way cable adjuster and lever slack adjuster may need to be adjusted for correct cable slack.
14.My factory shop manual lists 2-3mm as the correct play in the lever after the cable has been properly tensioned.
15.Re-install the covers, and shifter lever, start the engine to check the shifting action.
16.These engines have a shifting lock out to prevent moving in any gear higher than second unless the engine is running and proper shifting is done.
Clutch Cable Replacement On Some Kawasaki Motorcycles
With Proper Mechanism Adjustments
1.About mid way down the clutch cable is an adjuster; shorten the cable as much as possible.
2.Remove the small cover on the left side of the sprocket cover and loosen up the lock nut on the clutch throw out mechanism.
3.Remove the shifter lever; the sprocket cover, and lay the cover on some rags or news papers.
4.Have on hand a small cotter pin that will be needed to prevent the new clutch cable from coming out of the throw out mechanism.
5.At the left handlebar turn in the slack adjusters for the clutch cable and then take out the pivot bolt.
6.New clutch cables may or may not have lubrication; now's the time to either hang the new cable up overnight so heavy oil can flow through it or buy a cable luber kit with the special clamp and can of spray lube.
7.Attach the cable to the cover's throw out mechanism and secure it with a new cotter pin.
8. While you're in there, check the wiring from the alternator(YELLOW WIRES, or any wires from the alternator), remove the excess chain lube from the clutch push rod and check the wire routing that goes above the engine sprocket.
9. Check the lock washer for cracks on the engine sprocket and any "Hooking" of the sprocket teeth.
10 Route the clutch cable the same way the old one was and connect the cable to the clutch lever; and the pivot bolt gets re-installed.
11.Carefully install the sprocket cover, making sure the push rod is engaged and then tighten up the cover.
12.Adjusting the clutch play and cable tension is real easy; using a flat bladed screwdriver, turn the slotted screw clockwise(to the right) until it becomes hard to turn; then turn it counterclockwise(to the left) 1/4 turn and tighten the lock nut.
13.The mid way cable adjuster and lever slack adjuster may need to be adjusted for correct cable slack.
14.My factory shop manual lists 2-3mm as the correct play in the lever after the cable has been properly tensioned.
15.Re-install the covers, and shifter lever, start the engine to check the shifting action.
16.These engines have a shifting lock out to prevent moving in any gear higher than second unless the engine is running and proper shifting is done.
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- jacksdad
-
- Offline
- User
-

Registered
- 1979 kz 750 OUCH, IT SPARKED
- Posts: 161
- Thanks: 2
Re: clutch cable
04 Jul 2011 23:54
so where is the least expensive place to get a clutch cable?
, mine broke shifting from first to second coming off a red light?
, mine broke shifting from first to second coming off a red light?
1979 kz750 twin cyl.
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: clutch cable
05 Jul 2011 00:12
Try Z1E and don't forget to lube all cables.
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- martin_csr
-
- Offline
- User
-

Registered
- Posts: 7993
- Thanks: 1648
Last edit: 15 Feb 2013 11:16 by martin_csr.
Please Log in or Create an account to join the conversation.
- jacksdad
-
- Offline
- User
-

Registered
- 1979 kz 750 OUCH, IT SPARKED
- Posts: 161
- Thanks: 2
Re: clutch cable
05 Jul 2011 12:29
thanks guys, the cable measures 58 and 3 quarters long annd they have one that says it it 58 and 1/2 long, says it fits the 1976-79 kz750 nad the bars are stock. Thank ya'll very much for letting me know to lube it first, what do I lube it with anyway?
1979 kz750 twin cyl.
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: clutch cable
05 Jul 2011 13:35
I lube mine with clean motor oil. I just make a little Saran Wrap funnel and twist-tie it to the top of the cable. I put about a couple tablespoons of oil in it and hang it overnight. You must put something under the bottom end to catch the excess oil or you will wake up to a mess (how do I know this?) On the clutch cable, wrap the center adjuster with Saran Wrap and twist tie it in a fashion that will allow the oil to flow to the bottom section of cable but not run out at that point. This maintenance should be done to all cables at least every other year (or more if you ride a lot in dusty or wet conditions). And as Martin pointed out, be sure to lube the ends of the cable (especially where they fit into the handlebar levers) as that is where the greatest probability of wear & breakage is. I use white lithium grease for the ends. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Please Log in or Create an account to join the conversation.
- martin_csr
-
- Offline
- User
-

Registered
- Posts: 7993
- Thanks: 1648
Last edit: 15 Feb 2013 10:48 by martin_csr.
Please Log in or Create an account to join the conversation.
- jacksdad
-
- Offline
- User
-

Registered
- 1979 kz 750 OUCH, IT SPARKED
- Posts: 161
- Thanks: 2
Re: clutch cable
05 Jul 2011 19:16
rednecky works for me, I could use all the redneck ingenuity you have, thanks gents
1979 kz750 twin cyl.
Please Log in or Create an account to join the conversation.
- racer54
-
- Offline
- User
-

Registered
- Posts: 1902
- Thanks: 114
Re: clutch cable
05 Jul 2011 19:24
Did you take the clutch actuator off the cover itself? I'm talking about the worm gear that fits into the housing that bolts to the cover. If you did, you can be off one tooth and it will be hard to get everything right. I've been through that and it can be a real headache til you figure out the problem and go back and move it one tooth...then it works fine. Just a thought!
1980 LTD (changed over the years), 1979 LTD (being rebuilt), 1977 KZ turbo and various KZ's in various states of build. KLX110
Please Log in or Create an account to join the conversation.
- jacksdad
-
- Offline
- User
-

Registered
- 1979 kz 750 OUCH, IT SPARKED
- Posts: 161
- Thanks: 2
Re: clutch cable
07 Jul 2011 12:10
same subject different guy--- the clutch cable I ordered came today (wooohooo) appearantly I ordered the wrong one I got the one for a KZ750e and I have a KZ750 B will it work or should i exchange it?
1979 kz750 twin cyl.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
