Rev limit?

  • Robwolf
  • Robwolf's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • It's ugly, but it moves!
  • Posts: 110
  • Thanks: 2

Rev limit?

01 Jul 2011 15:24
#460490
My bike is acting like it has a rev limiter around 7500-8000 rpms. Which is a bit of a problem when the sweet spot for it's power is closer to 9000, and when 6th gear only gets you around 1000/10 rpm/mph. I have a KZ400H. The carbs are functioning as they should now, with both plugs showing a coffee color when pulled. The exhaust is open with no mufflers or baffles. Is the lack of back pressure causing this problem?
'79 Kz400H1 'cafe' and '94 En500 Vulcan in swampy Florida.

Please Log in or Create an account to join the conversation.

  • TeK9iNe
  • TeK9iNe's Avatar
  • Offline
  • User
  • User
    Registered
  • What did you do!?!
  • Posts: 2436
  • Thanks: 28

Re: Rev limit?

01 Jul 2011 17:48
#460508
Not likely. I would say try a smaller gap, or hotter coils. Sounds like you're getting blow-out.

Tan plugs = older coils, or jetting too rich with unleaded gas. The plugs should look very clean with inly a light soot ring around the base thread and a very faint wisp of soot/darkening around the the porcelin where it meets the metal body. Thats max power with good ignition system.

Good luck.

B)
Motorcycle Shop Owner/Operator

79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors ;)
The following user(s) said Thank You: Robwolf

Please Log in or Create an account to join the conversation.

  • Robwolf
  • Robwolf's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • It's ugly, but it moves!
  • Posts: 110
  • Thanks: 2

Re: Rev limit?

01 Jul 2011 17:54
#460511
I will try adjusting the gap. My coil is new as of January, so it should be good to go. Now to go get a gap tool.
'79 Kz400H1 'cafe' and '94 En500 Vulcan in swampy Florida.

Please Log in or Create an account to join the conversation.

  • Robwolf
  • Robwolf's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • It's ugly, but it moves!
  • Posts: 110
  • Thanks: 2

Re: Rev limit?

01 Jul 2011 18:14
#460517
So, aside from a ticket and needing hearing-aids later in life, what issues might be caused by open pipes. I like the louder rougher sound. I just put, what I call, temporary baffles in to reduce noise (mighta overdone it).
'79 Kz400H1 'cafe' and '94 En500 Vulcan in swampy Florida.

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Rev limit?

01 Jul 2011 19:28
#460533
Robwolf wrote: My bike is acting like it has a rev limiter around 7500-8000 rpms. Which is a bit of a problem when the sweet spot for it's power is closer to 9000, and when 6th gear only gets you around 1000/10 rpm/mph. I have a KZ400H. The carbs are functioning as they should now, with both plugs showing a coffee color when pulled. The exhaust is open with no mufflers or baffles. Is the lack of back pressure causing this problem?
Yes, it sure is. You need bigger main jets running open pipes.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • bountyhunter
  • bountyhunter's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 7245
  • Thanks: 338

Re: Rev limit?

01 Jul 2011 19:29
#460534
Robwolf wrote: So, aside from a ticket and needing hearing-aids later in life, what issues might be caused by open pipes.
The flow rate won't match the needle taper. You may be able to jet up enough to get it to run OK, but it will not run as well as stock did across the full RPM range.
1979 KZ-750 Twin

Please Log in or Create an account to join the conversation.

  • ELCouz
  • ELCouz's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 376
  • Thanks: 5

Re: Rev limit?

01 Jul 2011 19:36 - 01 Jul 2011 19:39
#460535
You need bigger main jets running open pipes.

+1 on that...passed from stock exhaust to freeflow (no baffle) type exhaust required me to increase 2 size of main jets to be ok with no flat spot... YMMV !!

and replace stock air filter box with pods.... you need bigger main/pilot jets too...sensitivity to wind and rain ftw!

Pods pods pods...that curse! That's why i won't even touch a pod with a 10 feet pole!

regards,
laurent
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe
Last edit: 01 Jul 2011 19:39 by ELCouz.

Please Log in or Create an account to join the conversation.

  • Robwolf
  • Robwolf's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • It's ugly, but it moves!
  • Posts: 110
  • Thanks: 2

Re: Rev limit?

24 Jul 2011 15:31
#464623
Yeah, I was thinking about going with pods for the looks, but decided to say eff that when I realized I'd need to re-jet. Not really in the mood for performance upgrades at the moment. Mostly just want it to run right and look good. So I got some materials to make baffles and will be installing them when I can. Until then she's running all right, I forgot that I had retarded the timing when it was racing with no input from me. After I brought it back to at least TDC ( I've advanced it some now, ) that 7-8k rev-limit went away. It gets a brief stumble around there now but holds on to at least an even 10k before it decides enough is enough and I shift.
'79 Kz400H1 'cafe' and '94 En500 Vulcan in swampy Florida.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum