Breather question

  • 1980kz550
  • 1980kz550's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 8
  • Thanks: 0

Breather question

03 Jul 2011 16:53
#460777
I am putting pods on my bike, and I was curious what some of the people have done here with the breather that plugs into the airbox from the crankcase. I was wondering if you could just run a hose up from that to the crancase ventilation system up top, or if there is just a breather you can put on top of it, and where to get one. I know somebody on here has put pods on one of these things. Any help would be great!

Thanks,
Nick

Please Log in or Create an account to join the conversation.

  • JR
  • JR's Avatar
  • Offline
  • Sustaining Member
  • Sustaining Member
    Registered
  • Posts: 2981
  • Thanks: 500

Re: Breather question

03 Jul 2011 20:58 - 03 Jul 2011 21:01
#460820
I had one of these - scroll down for the ones with the hose clips attached - on mine.

www.knfilters.com/vent.htm

or from Z1 enterprises www.z1enterprises.com/Air-Filter--KN-621...ent-Filter-2628.aspx

I think some people just run a longer hose and route it between swingarm and motor.
1980 kz750E1, Delkevic exhaust
Last edit: 03 Jul 2011 21:01 by JR.

Please Log in or Create an account to join the conversation.

  • 1980kz550
  • 1980kz550's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 8
  • Thanks: 0

Re: Breather question

04 Jul 2011 13:31
#460946
Ok thats kinda what I figured. thanks. But what do you do with the stuff under the fuel tank that used to plug into the factory air box? It looks kinda like some sort of crankcase breather with a hose that extends a little past the carbs.

Please Log in or Create an account to join the conversation.

  • loudhvx
  • loudhvx's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 10863
  • Thanks: 1622

Re: Breather question

04 Jul 2011 14:48 - 04 Jul 2011 15:32
#460960
Remove it and make sure both big ports are capped, (or connected together with a hose), so no air gets in. That system sucks clean air from the airbox to inject into the exhaust system. It doesn't affect jeting or performance, but just allowed more burning in the exhaust. It will cause backfires if it leaks fresh air. Ape, and other sources have block-off plates for the air suction plates. (Beware, the 550, 750, and 1000 all use different size plates even though they look really similar.

There should be two small vacuum lines going to the intake manifolds. They should be capped off as well.

For the crankcase breather, I tapped the hole for pipe thread, put in an elbow, and attached a hose to run down to the ground. (Incidently, 550, 650, and 750-4 all use same size crank breather plate.)











Last edit: 04 Jul 2011 15:32 by loudhvx.

Please Log in or Create an account to join the conversation.

  • 1980kz550
  • 1980kz550's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 8
  • Thanks: 0

Re: Breather question

06 Jul 2011 01:13
#461238
Awesome! Thank you for the pictures those help a lot. Did you put bigger jets with the pods I've heard mixed results with people even having to do that with these bikes. I've also read a lot of mixed results about putting pods on in the first place. But I am going to anyways because I like to tinker.

Thanks again,
Nick

Please Log in or Create an account to join the conversation.

  • loudhvx
  • loudhvx's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 10863
  • Thanks: 1622

Re: Breather question

06 Jul 2011 13:46 - 06 Jul 2011 14:01
#461317
Pods work well on the TK-22 carbs. They are easy to jet because they are not cv carbs.

On the KZ550D1 1981 GPZ550, pods do make you need a little more throttle from a stop, especially if you have a passenger. But it is smooth and you can get used to it quickly. It has noticably more zing on the highway.

The standard KZ550A and LTD KZ550C have more low end torque to begin with, so you might not even notice the difference on the low end.

You will have to rejet, most likely. The easiest way, is also the expensive way, and that is to get a Dynojet kit. The best part of the kit is that it has single-taper needles which are a little easier to tune, in my opinion.

Rebuild kits come with stock mains and pilots, but also, more importantly, come with adjustable versions of the stock needles. So this route costs less and you get a lot more parts.

Or you can tinker with main jets using small-head Keihin mains. Their numbers are like the tk mains in that the numbers are just the hole diameter in hundredths of millimeters. They may flow differently than the stock mains, so the numbers may not correspond directly, but in experience, they are close enough to give a good idea.

Generally speaking you will want jets in the 94 to 98 range depending on your exhaust. You may want to go with larger pilots, but they do not exist. You have to drill them. Luckily the rebuild kits come with new ones in case you screw up. Stock is 32, you will want 34 or possibly 37, but no larger.

The airscrew settings will be closer to 2 ~ 2.5 turns out.

In addition to the manual in my signature, you will want to look at this page.
You will probably want a couple hours to go through it.


home.comcast.net/~loudgpz/GPZweb/TK22mainPage/TK22mainPage.html

It is not a substitute for the manual, but just additional info.


I have several bikes. Some have pods, some have airbox. Their are advantages to both. I would be missing some of the gpz fun if I stuck with the only the airbox, however, don't throw away the airbox or any of the boots or mounting hardware. That stuff is hard to come by, and you may want to go back to the airbox... mainly if you find yourself riding in the rain a lot.

When they are tuned right, pods or airbox run and idle just as smooth as the stock setup. ( Even CV carbs can be setup to run great with pods, but it's a lot more work. As you said, tinkering is a big part of the fun on these old bikes.)

BTW, I recommend the Emgo pods (39mm) at Z1enterprises. They are disposable and very low cost... especially good if you may want to go back to the airbox. Cleaning and oiling K&N or UNI pods are a major hassle and you get covered in goo anytime you try to adjust the idle etc, not to mention they cost a fortune plus the oil and cleaners are expensive too.
Last edit: 06 Jul 2011 14:01 by loudhvx.

Please Log in or Create an account to join the conversation.

  • Beard
  • Beard's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 74
  • Thanks: 0

Re: Breather question

07 Jul 2011 00:26
#461459
what i ended up doing as a quick fix..... read, still this way... take 3 pieces of screen, cut about 2x the size of the hole and stack them so they cross each other... lay them over the hole.. then take a proper sized piece of rubber hose and push it down over the screen and over the bung there.
79 KZ650B
Jack of everything, Master of nothing.

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum