Minimum I.D. for fuel flow (810cc engine)
- ELCouz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 376
- Thanks: 5
Minimum I.D. for fuel flow (810cc engine)
08 Jul 2011 22:47
Hi,
I'm slowly looking to buy a 12v solenoid inline fuel shutoff valve to bypass the vacuum petcock (sealed vacuum ports).
What is the minimum size of tubing to not restrict the fuel which is gravity fed.
Engine size is 810cc... is 1/4 enough?
I'm looking here www.dan-marc.com/rv-parts-12-volt-fuel-shut-off-valves.html
Some have built in fuel filter
they are cheap!
best regards,
laurent
I'm slowly looking to buy a 12v solenoid inline fuel shutoff valve to bypass the vacuum petcock (sealed vacuum ports).
What is the minimum size of tubing to not restrict the fuel which is gravity fed.
Engine size is 810cc... is 1/4 enough?
I'm looking here www.dan-marc.com/rv-parts-12-volt-fuel-shut-off-valves.html
Some have built in fuel filter
they are cheap!
best regards,
laurent
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Minimum I.D. for fuel flow (810cc engine)
09 Jul 2011 09:04
why not just put in a manual shut off petcock ?
1/4" is fine.
i ran the stock 1/4" line on my kz900 with an 1135cc and 33mm carbs.
1/4" is fine.
i ran the stock 1/4" line on my kz900 with an 1135cc and 33mm carbs.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- ELCouz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 376
- Thanks: 5
Re: Minimum I.D. for fuel flow (810cc engine)
09 Jul 2011 10:16 - 09 Jul 2011 10:18why not just put in a manual shut off petcock ?
1/4" is fine.
i ran the stock 1/4" line on my kz900 with an 1135cc and 33mm carbs.
It's easier just to put the valve on 12V ignition so when i turn off the key fuel shut off automatically!
I'm the type of guy that forget basic stuff like leaving with petcock ON !
Carb should normally not overflow.
If forget to close the petcock and it do overflow (stuck needle happen sometimes rarely thought) that will cost me another oil change and could be worse if it is no possible to do the oil change (ex: not at home)
regards,
laurent
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe
Last edit: 09 Jul 2011 10:18 by ELCouz.
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: Minimum I.D. for fuel flow (810cc engine)
09 Jul 2011 11:04
Interesting idea - any reviews on reliability of those shut-offs? I'd hate to be on a trip and have one fail, might want to buy two
Please Log in or Create an account to join the conversation.
- DoubleDub
-
- User
-

Public
- Thanks: 0
Re: Minimum I.D. for fuel flow (810cc engine)
09 Jul 2011 11:05
These caught my eye, too...
www.dan-marc.com/rv-and-marine-parts-fuel-flow-meters.html
Too bad the dash on these bikes is so small....and with stock gauges it's hard to add a lot of gadgets without it looking wrong.
www.dan-marc.com/rv-and-marine-parts-fuel-flow-meters.html
Too bad the dash on these bikes is so small....and with stock gauges it's hard to add a lot of gadgets without it looking wrong.
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Minimum I.D. for fuel flow (810cc engine)
09 Jul 2011 12:30
No triing to change your mind , but if the float valve fails the fuel should come out the over flow tube.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- ELCouz
-
Topic Author
- Offline
- User
-

Registered
- Posts: 376
- Thanks: 5
Re: Minimum I.D. for fuel flow (810cc engine)
09 Jul 2011 13:50 - 09 Jul 2011 13:53but if the float valve fails the fuel should come out the over flow tube.
Mikuni BS34 have only vents and lack of overflow barbs...it will leak to engine intake
Interesting idea - any reviews on reliability of those shut-offs? I'd hate to be on a trip and have one fail, might want to buy two
Test for 100 000 cycles (ON/OFF) should be way more that the motorcycle life !
And also a bypass is easy to do just in case...unplug tubing from valve to the petcock directly! you can do that on the side of the road !
EDIT: yeah fuel meter gauge (MPG display is sweet!) looks very nice! 55 mm diameter thought! Not too expensive 159$
regards,
laurent
1982 KZ810-R1 GPZ with hindle 4-into-1 pipe
Last edit: 09 Jul 2011 13:53 by ELCouz.
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Minimum I.D. for fuel flow (810cc engine)
09 Jul 2011 14:11
I see.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
