Cam chain tensioner sprockets
- Chaotic Reason
-
Topic Author
- Offline
- User
-

Registered
- Posts: 384
- Thanks: 15
Cam chain tensioner sprockets
09 Jul 2011 18:08 - 10 Jul 2011 01:17
Removed the head on my E-2 today to replace the gaskets. I was inspecting all the parts in the area because i was hearing a slight grinding sound when I would give it some gas, and noticed that the sprockets had a bit of play.
When it was idling, there was no sound, only when I would give it gas. I noticed on the sprockets that are part of the cam chain tensioning system, when I hold the rod that the sprocket is on, I can feel a slight play in the bearings of that sprocket. I can feel this play in both of the sprockets, front and rear.
So if I'm holding the rod horizontal, and looking at the sprocket on a vertical axis, I can move the sprockets slightly away from vertical, in both directions.
Is this normal? I'm posting this on my iPod, so I can't upload any photos till tonight, but does this sound like normal wear and tear? I know, when in doubt, replace it, but I'm broke! HELP!!!
Ps, I also noticed that one of the wee rubber blocks was not on one side of the rod holding the sprocket in place. Where can you even get those??? Can I just make one? Or does it have to be specific material, thickness, and so on?
Attachment DSCF0916_2011-07-10.JPG not found
When it was idling, there was no sound, only when I would give it gas. I noticed on the sprockets that are part of the cam chain tensioning system, when I hold the rod that the sprocket is on, I can feel a slight play in the bearings of that sprocket. I can feel this play in both of the sprockets, front and rear.
Attachment DSCF0917_2011-07-10.JPG not found
So if I'm holding the rod horizontal, and looking at the sprocket on a vertical axis, I can move the sprockets slightly away from vertical, in both directions.
Is this normal? I'm posting this on my iPod, so I can't upload any photos till tonight, but does this sound like normal wear and tear? I know, when in doubt, replace it, but I'm broke! HELP!!!
Ps, I also noticed that one of the wee rubber blocks was not on one side of the rod holding the sprocket in place. Where can you even get those??? Can I just make one? Or does it have to be specific material, thickness, and so on?
Michael
1980 KZ1000 shaft drive
1980 KZ1000 shaft drive
Last edit: 10 Jul 2011 01:17 by Chaotic Reason.
Please Log in or Create an account to join the conversation.
- KZ_Rage
-
- Offline
- User
-

Registered
- Kentucky Bourbon Barrel Ale
- Posts: 891
- Thanks: 19
Re: Cam chain tensioner sprockets
10 Jul 2011 11:48
Not sure how much "slightly" is but it shouldn't have enough to be noticeable. There has to be a tiny, tiny amount of play in bearing or they will heat, too much and they will skid, either way a failure is coming sooner or later.
If in doubt you can replace them, you are after all in this deep on a tear-down and have had a timing chain noise issue, probably don't want to go back in later and spend the money on another set of gaskets.
If unsure and you can find someone nearby that is a trusted mechanic on old air cooled Kaw bikes you can have him take a look at them to see but that is trusting another person not to be a "just run it until it gets worse and replace it later" kind of guy.
If in doubt you can replace them, you are after all in this deep on a tear-down and have had a timing chain noise issue, probably don't want to go back in later and spend the money on another set of gaskets.
If unsure and you can find someone nearby that is a trusted mechanic on old air cooled Kaw bikes you can have him take a look at them to see but that is trusting another person not to be a "just run it until it gets worse and replace it later" kind of guy.
1979 KZ1000E1 SOLD!
1984 KZ550F2 SOLD!
2006 ZG1000A6F (Totaled)
2001 ZRX1200R (Sold)
2001 Sprint 955i ST (daily rider)
1984 KZ550F2 SOLD!
2006 ZG1000A6F (Totaled)
2001 ZRX1200R (Sold)
2001 Sprint 955i ST (daily rider)
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Cam chain tensioner sprockets
10 Jul 2011 12:25
u can get the rubber blocks and gears from Z1E. u are likely in for about $400. change the chain too.the rubber around the gears gets hard and brittle from years of heat and then chips and breakes up and goes in the motor. this is much more common than bearing wear.
actualy i have a brand new heavy dudy chain still in the box. if interested pm me for a deal.
actualy i have a brand new heavy dudy chain still in the box. if interested pm me for a deal.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
