inconsistant cam chain tension??
- dogodell
-
Topic Author
- Offline
- User
-

Registered
- Posts: 9
- Thanks: 0
inconsistant cam chain tension??
27 Jul 2011 14:21
hello all and thanks in advance for the help
I have a 1985 zn1100 ltd that I picked up a few months ago...
I am in the process of making sure the valve clearance is in spec and noticed something strange with the cam chain...
while turning the bike via the 17mm nut in order to check each valve i noticed that the cam chain goes from very tight in between the cams to all of a sudden no tension at all to the extent that it actual droops down some... I don;t know if its helpful or not but the exact point with no tension is about where the 1st T mark on rotor lines up with case timing mark
the bike has an ape manual tensioner on it which was set with the valve cover on according to the instructions that came with it...
using a flashlight and visually inspecting the chain it doesn't appear to have any kinks or to be missing any teeth etc on the gears it comes in contact with...
is this normal and just because the valve cover and the top cam guide isn't in place and if not any ideas as to what could be causing it???
thanks again and sorry for the long post just wanted to try and include as many details as possible
I have a 1985 zn1100 ltd that I picked up a few months ago...
I am in the process of making sure the valve clearance is in spec and noticed something strange with the cam chain...
while turning the bike via the 17mm nut in order to check each valve i noticed that the cam chain goes from very tight in between the cams to all of a sudden no tension at all to the extent that it actual droops down some... I don;t know if its helpful or not but the exact point with no tension is about where the 1st T mark on rotor lines up with case timing mark
the bike has an ape manual tensioner on it which was set with the valve cover on according to the instructions that came with it...
using a flashlight and visually inspecting the chain it doesn't appear to have any kinks or to be missing any teeth etc on the gears it comes in contact with...
is this normal and just because the valve cover and the top cam guide isn't in place and if not any ideas as to what could be causing it???
thanks again and sorry for the long post just wanted to try and include as many details as possible
1985 zn1100 ltd...
daily driver rain or shine and currently my only vehicle
daily driver rain or shine and currently my only vehicle
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: inconsistant cam chain tension??
27 Jul 2011 14:28
yes with the valve cover off, the guide is not there to hold tension down on the chain between the sprockets. When installing again, still might be a good idea to loosen the APE a little to be sure the chain has slack. Mostly if a slightly thinner VC gasket it used.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- dogodell
-
Topic Author
- Offline
- User
-

Registered
- Posts: 9
- Thanks: 0
Re: inconsistant cam chain tension??
27 Jul 2011 14:41
hey sorry I was wrong the first time the mark on the ignition rotor is actual the farthest one along (sorry no camera) but not the one associated with T (1st mark) F (2nd mark) but the one directly above the 4 (3rd mark) in the 1.4 ...
also is seems to go slack at this point regardless of cam position...
thanks again
also is seems to go slack at this point regardless of cam position...
thanks again
1985 zn1100 ltd...
daily driver rain or shine and currently my only vehicle
daily driver rain or shine and currently my only vehicle
Please Log in or Create an account to join the conversation.
- dogodell
-
Topic Author
- Offline
- User
-

Registered
- Posts: 9
- Thanks: 0
Re: inconsistant cam chain tension??
27 Jul 2011 14:43
Thanks Motor Head...
my internet sucks and I didn't refresh to read your post before adding the details!!
my internet sucks and I didn't refresh to read your post before adding the details!!
1985 zn1100 ltd...
daily driver rain or shine and currently my only vehicle
daily driver rain or shine and currently my only vehicle
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
