exhaust pop
- newowner79kz750b1
-
Topic Author
- Offline
- User
-

Registered
- 79 kz750b4
- Posts: 114
- Thanks: 0
exhaust pop
30 Jul 2011 15:22
i have a kz750 twin. just bought it. changed the plugs. cleaned the carbs. ran sea foam through the bike and cleaned the carbs again. adjusted the floats with the clear tube method. everything im doing is making the bike run better and better but just not quite right. it starts and idles great. but, the left side exhaust is popping. and it sputters upon takeoff. and the popping kinda of stops once i take off and im in like 2nd gear but still kinda of sputters a tad. im thinking i need to adjust the float a little more more to make it more rich but not sure.any help is greatly appreciated.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: exhaust pop
30 Jul 2011 15:34
I would check compression and valve clearance first. If good, it's probably a carburetion problem or vacuum leak.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: exhaust pop
30 Jul 2011 15:38 - 30 Jul 2011 15:45
Your thinking is close. The popping is being caused by the sudden introduction of air into the fuel stream - or the spark plug is missfiring.
If compression is good across all cylinders... valves are set? OK... Use a timing light to check if it is sparking everytime.
Make certain that the carb holders (bolted to engine) are actually sealed perfectly. Best to pull them off and use some Permatex Motoseal (gray tube - gas resistant) to seal them to the engine.
Make sure that the clamps are firm and there are no air leaks at the intake and airbox side of carbs - make sure airbox/filter are all completely sealed and seated correctly.
Make sure exhaust is not leaking at the head. Make certain nuts are tight on header.
Check the air/mixture screw adjustments are correct and not accidentally completely seated. Set to spec, or about 1.5 turns out form lightly seated to start.
All fuel levels should be within 1mm of eachother, and spec - usually 2-3mm below the edge above carb bowl.
MOST IMPORTANT: make sure the pilot jet is clean and can be seen thru when held up to a light. Using carb cleaner straw, spray through the pilot passage in the carbs and make sure that the spray comes out all the tiny holes in the carb bore - look to see if its the same for both carbs!
Lastly, if you dont have the tools to perform a vacuum sync, do a bench sync and make sure that the slides/butterflys are opening as close as possible to the same amount on all carbs.
A vacuum sync is considered mandatory maintenence - and makes a big difference despite what some say...
Good luck!
If compression is good across all cylinders... valves are set? OK... Use a timing light to check if it is sparking everytime.
Make certain that the carb holders (bolted to engine) are actually sealed perfectly. Best to pull them off and use some Permatex Motoseal (gray tube - gas resistant) to seal them to the engine.
Make sure that the clamps are firm and there are no air leaks at the intake and airbox side of carbs - make sure airbox/filter are all completely sealed and seated correctly.
Make sure exhaust is not leaking at the head. Make certain nuts are tight on header.
Check the air/mixture screw adjustments are correct and not accidentally completely seated. Set to spec, or about 1.5 turns out form lightly seated to start.
All fuel levels should be within 1mm of eachother, and spec - usually 2-3mm below the edge above carb bowl.
MOST IMPORTANT: make sure the pilot jet is clean and can be seen thru when held up to a light. Using carb cleaner straw, spray through the pilot passage in the carbs and make sure that the spray comes out all the tiny holes in the carb bore - look to see if its the same for both carbs!
Lastly, if you dont have the tools to perform a vacuum sync, do a bench sync and make sure that the slides/butterflys are opening as close as possible to the same amount on all carbs.
A vacuum sync is considered mandatory maintenence - and makes a big difference despite what some say...
Good luck!
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Last edit: 30 Jul 2011 15:45 by TeK9iNe.
Please Log in or Create an account to join the conversation.
- jacksdad
-
- Offline
- User
-

Registered
- 1979 kz 750 OUCH, IT SPARKED
- Posts: 161
- Thanks: 2
Re: exhaust pop
30 Jul 2011 15:44
don't know if this helps or not, but when I got my bike about 6 months ago, I put seafoam in the gastank, until that was completely burned out, it popped quite alot, thik it has to do whith how hot the seafoam burns
1979 kz750 twin cyl.
Please Log in or Create an account to join the conversation.
- newowner79kz750b1
-
Topic Author
- Offline
- User
-

Registered
- 79 kz750b4
- Posts: 114
- Thanks: 0
Re: exhaust pop
30 Jul 2011 16:27
i dont have any way to check timing ect. im thinking its a fuel or spark problem though. because when i bought the bike the bike ran amazing, but only amazing the with the choke half way on. thats why i cleaned the bowls ect. it wasent popping then at all. last weekend i set the float because they were way off. ill have to check them again because i just made sure that they were within 4.5 to 6.5mm but didnt pay close enough attention to see how close they were to each other.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
