points, ignition, timing? im stuck

  • sitenonme
  • sitenonme's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 8
  • Thanks: 0

points, ignition, timing? im stuck

02 Aug 2011 00:54
#466292
ok...so i bought a 1978 kz650 from a guy who goes away months at a time for him work and he said whenever he comes home he goes to start the bike but everytime it wont fire and he has to clean the carbs...i picked it up for 320 and it was in beautiful condition and i was just expecting drain the gas new plugs and a good carb cleaning...i unloaded it and was rolling it down my long driveway and was attempting to bump it...why not...it started after a few tries and ran finaky then i gassed it and it took off fine...i rode it around the block and it went thru all gears fine so i put inside and did what i had originally planned...i put like 60 miles on it with maybe 4 or 5 different rides but i could tell it should have more power than it did and it would redline at 6500 to7000 rpms and it was really rough whenit hit 5000...it would idle perfect and rev like it just came out of the shop so i was puzzled...out of my stupidity i took off the left cover thats sheilds the big circle magnet and i turned the 17mm bolt both ways (counter and clockwise) a few rotations...i then started it and rode it for a few miles going as fast as it would go and it ran the same as before...a couple days later i went to start it and it took a while to start but it did and it was running really strangley to where it would die if i gave it too much gas but i could slowly give it gas and the rpms would crwal higher but i just parked it...the next day i went to start it and it was running even worse! so i just shut it off cause it would either just die or i couldnt gain any rpms at all and the number 4 cyl. wasnt getting hot when the other three were (hadnt been that way before)...then the next day i went out to strat it and there wasnt even the littlest hope for it to fire at all...i went to gap the points and they were so bad that neither of them would open at all when i cranked the engine...the points looked good and functioned but the were set so the didnt open at all...i adjusted them properly and there is a spark in a plug wires and in both points when i kick it and the plugs r perfect...i havent adjusted the timing but im not sure what is wrong...all other electrical things work perfect and im just baffled...i just ordered the dyna s and dyna coils with dyna plug wires and i hope that cures it but i have a feeling its something else... also before i read too thuroughly into the manuel on gapping the points i used the 13mm nut to crank the engine in the clockwise position probably 3 or 4 rotations...did i forsure ruin the advance timing ignition or could it still be good? plz help... and thanks in advance!

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: points, ignition, timing? im stuck

02 Aug 2011 01:08 - 02 Aug 2011 01:14
#466296
Hello, sitenonme, and WELCOME to KZr! :cheer:

Correct installation of Dyna coils, Dyna-S and Dyna plug wires, together with brand new spark plugs per factory specs, should resolve any ignition issues, provided the advancer is cleaned and lubed and functioning properly, and the timing is set correctly.

Would also check the valve clearances to determine whether any of them are way out of spec.

The carbs likely need a good cleaning. As does the petcock. And a tank flush wouldn't hurt either.

In not already done, be sure to install a good after market in-line fuel filter (or two of them if dual fuel lines are fitted).

Good Fortune! :)
1973 Z1
KZ900 LTD
Last edit: 02 Aug 2011 01:14 by Patton.

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: points, ignition, timing? im stuck

02 Aug 2011 01:14
#466297
sitenonme wrote: ...used the 13mm nut to crank the engine in the clockwise position probably 3 or 4 rotations....

The 13mm bolt threads into the crankshaft.
It should never be used to hand rotate the crankshaft, because it is prone to snap off inside the crank shaft.

There's a separate 17mm "fake" nut that's designed for hand rotating the crankshaft, which should always be used for such purpose.

Good Fortune! :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • sitenonme
  • sitenonme's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 8
  • Thanks: 0

Re: points, ignition, timing? im stuck

02 Aug 2011 01:17
#466298
well i dont beleive it snapped or is broken in anyway so should the advance timing ignition be good?

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: points, ignition, timing? im stuck

02 Aug 2011 01:20
#466300
Likely no harm done. :)
1973 Z1
KZ900 LTD

Please Log in or Create an account to join the conversation.

  • remi
  • remi's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 1
  • Thanks: 0

Re: points, ignition, timing? im stuck

03 Aug 2011 17:00
#466611
I just had the same problem with a kz440 I just bought. The advancer was covered in rust and not moveing as it should. I cleaned and lubed it. set the timig and point. Now it rund good.

Please Log in or Create an account to join the conversation.

  • sitenonme
  • sitenonme's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 8
  • Thanks: 0

Re: points, ignition, timing? im stuck

11 Aug 2011 17:56
#468429
what would happen if the 13mm bolt did break inside...would it not start...cause i got the dyna s, coils, and plug wires all installed correctly and it has a beautiful stong spark but still wont even try to fire...i cleaned out the carbs again and still nothing...when im kicking it and i hold the gas it makes a stripping sound within the engine...so confused because if im not giving it has it wont make that sound....what is wrong?

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: points, ignition, timing? im stuck

11 Aug 2011 18:07
#468430
sitenonme wrote: what would happen if the 13mm bolt did break inside...would it not start...cause i got the dyna s, coils, and plug wires all installed correctly and it has a beautiful stong spark but still wont even try to fire...i cleaned out the carbs again and still nothing...when im kicking it and i hold the gas it makes a stripping sound within the engine...so confused because if im not giving it has it wont make that sound....what is wrong?

Are you holding the throttle open when trying to start the bike? If so, don't. To start a cold KZ650: tranny in neutral, fuel on, choke on, ignition on, hand off the throttle and kick; if using the electric starter also pull in the clutch lever. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • sitenonme
  • sitenonme's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 8
  • Thanks: 0

Re: points, ignition, timing? im stuck

12 Aug 2011 01:30
#468541
i just tried that a few times cause it had a spark and no fire so i thought it was starving for gas...its not my typical method for starting a bike haha but i am willing to try anything...im so puzzled with it

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum